M9106-xGx-2 Series Electric Non-Spring Return Actuators Catalog ...

M9106-xGx-2 Series Electric Non-Spring Return Actuators 

Code No. LIT-1900118 

Issued July 15, 2013 

Description 

The M9106-xGx-2 Series direct-mount electric 

actuators operate on AC 24 V power and are 

available for use with on/off, floating, or 

proportional controllers. These non-spring 

return actuators are easily installed on a 

Variable Air Volume (VAV) box, a damper with 

a round shaft up to 1/2 inch (13 mm) in 

diameter or a square shaft up to 3/8 inch 

(10 mm). The M9106 with a M9000-520 

linkage can also be used to position VG1000 

Series 1/2 in. (DN15) to 1-1/2 in. (DN40) ball 

valves. 

The M9106 Series models have 53 lb·in. 

(6 N·m) running torque. These actuators have 

a nominal 60-second travel time for 90° of 

rotation at 60 Hz (72 seconds at 50 Hz) with a 

load-independent rotation time. 

The M9106-xGC-2 models are available with 

integral auxiliary switches to perform switching 

functions at any angle within the selected 

rotation range. The -GGx models feature 

DC 0(2) to 10 V position feedback, and the 

-AGF models provide 10,000 ohm position 

feedback. 

Features 

• simple direct coupling reduces installation 

and commissioning time and improves 

reliability by eliminating damper linkages. 

Single screw coupling provides three-point 

shaft gripping. 

• designed for zone damper and ball valve 

actuator applications 

• small, compact design — allows installation 

in tight-fitting locations 

• on-off, floating and proportional control 

inputs 

• 60-second running time at 60 Hz 

• long life brushless synchronous drive motor 

technology – provides constant running 

time independent of load 

• robust 53 lb·in. (6 N·m) torque rating 

• whisper quiet 35 dBA noise rating 

• magnetic clutch – provides over torque 

protection over the entire range of rotation 

• -4 to 125°F (-20 to 52 °C) ambient 

temperature rating 

• 100,000 full stroke cycle, 2,500,000 

reposition rating 

• manual gear release simplifies setup and 

field adjustments 

• 1/2 in. NPT threaded conduit opening 

meets electrical code requirements and 

allows the use of flexible armored cable 

• position feedback (-GGX models) provides 

simple, closed-loop control with accurate 

position sensing. 

• adjustable rotation stops allow application 

versatility with 30 to 90° clockwise or 

counterclockwise rotation 

Applications 

The M9106 actuators are used to position 

balancing, control, round, and zone dampers 

in typical Heat, Ventilating, and Air 

Conditioning (HVAC) applications. The M9106 

can also be used with a M9000-520 linkage to 

control 1/2 in. (DN15) to 1-1/2 in. (DN40) 

VG1000 Series ball valves. The M9106 Series 

actuator mounts directly on the duct surface, 

round damper, or small rectangular damper 

with an anti-rotation bracket and two sheet 

metal screws (included). Additional linkages or 

couplers are not required. 

Refer to the damper or VAV box 

manufacturer’s information to select the 

proper timing for the actuator. Refer to the 

appropriate application note for specific wiring 

diagrams and information. 

Selection Charts 

M9106-xGx-2 Electric Non-Spring Return Actuators 

Code Number Control Type Torque / Voltage Auxiliary Switches Comments 

M9106-xGx-2 Series 

Electric Non-Spring Return Actuator 

For more information, refer to the 

M9106-xGx-2 Electric Non-Spring Return 

Actuators Product Bulletin (LIT-2681123) or 

the M9106-xGx-2 Electric Non-Spring Return 

Actuators Installation Instructions 

(Part No. 34-636-1085). 

Repair Information 

If the M9106-xGx-2 Electric Actuator fails to 

operate within its specifications, replace the 

unit. For a replacement actuator, contact the 

nearest Johnson Controls® representative. 

M9106-AGA-2 1 Floating 

53 lb·in. (6 N·m) None 

M9106-AGC-2 1 

60 second timing at 

60 Hz 

2-SPDT 

M9106-AGF-2 1 Floating with resistive feedback AC 24 V 50/60 Hz None 10,000 Ohm Feedback Pot 

M9106-GGA-2 DC 0(2) to 10 V 

None 

DC 0(2) to 10 V Feedback 

M9106-GGC-2 DC 0(4) to mA proportional 

2-SPDT 

M9106-IGA-2 On-Off / Floating with timeout None Adjustable timing 1, 1.5, 2, 5.5 or 11 min. 

M9106-IGC-2 

2-SPDT 

1. To avoid excessive wear or dive time on the motor for the AGx models, use a controller and/or software that provides a time-out function to remove the signal at 

the end of rotation (stall). The -GGx and -IGx models have an auto shutoff to avoid excessive wear or drive time on the motor. 

The performance specifications are nominal and conform to acceptable industry standards. For applications at conditions beyond these specifications, consult the local Johnson Controls office. 

Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2013 Johnson Controls, Inc. 

www.johnsoncontrols.com 

1

M9106-xGx-2 Series Electric Non-Spring Return Actuators (Continued) 

Accessories for M9106-xGx-2 Actuators 

Code Number Description 

CBL-2000-1 

CBL-2000-2 

CBL-2000-3 

DPT-2015-0 

DMPR-KC003 

20 in. (0.5 m) Wiring Harness, UL accepted for plenum use, connects the M9106 and DPT-2015 to the VAV controller 

20 in. (0.5 m) Plenum Rated Wiring Harness 

72 in. (1.8 m) Plenum Rated Wiring Harness 

0 to 1.5 in. W.C. (0 to 374 Pa) differential pressure transmitter 

Square Head Blade Pin Extension without Bracket supplied with Johnson Controls 

CD-1300 dampers and may be ordered separately for all direct mount applications 

DMPR-KC010 Adjustable Blade Position Indicator Switch Kit with total switching load limited to 2000 VA for the following applications: 

Pilot Duty: AC 24 V, 50 VA; AC 125/250/277 V, 125 VA 

Motor Load: AC 125/250/277 V, 1/3 hp 

Resistive Load: AC 125 V, 11 A; AC 250 V, 8 A; AC 277 V, 7 A (all maximum values) 

DMPR-KC011 Hex Head Blade Pin Extension without Bracket 

DMPR-KC012 Hex Head Blade Pin Extension with Bracket 

DMPR-KC213 Damper Jackshaft 1/2 in. Diameter, 1 Panel 

DMPR-KC214 Damper Jackshaft 1/2 in. Diameter, 2 Panel 

M9000-105 Pluggable 3-Terminal Block 

M9000-106 Pluggable 4-Terminal Block 

M9000-160 Replacement anti-rotation bracket for M9106 Series actuators 

M9000-200 Commissioning Tool provides a control signal to drive on/off, floating, proportional, or resistive actuators 

M9000-520 Valve Linkage Kit for field mounting an M9106 Series actuator to a 1/2 in. (DN15) to 1-1/2 in. (DN40) VG1000 Series ball valve 




2

M9106-xGx-2 Series Electric Non-Spring Return Actuators (Continued) 

Technical Specifications 

M9106-xGx-2 Electric Non-Spring Return Actuators 

Power Requirement AGx: AC 20-30 V at 50/60 Hz, 2.5 VA Supply, Class 2 

IGx: AC 20-30 V at 50/60 Hz, 2.8 VA Supply, Class 2 

GGx: AC 20-30 V at 50/60 Hz, 3.2 VA Supply, Class 2 

Control Type 

AGx: Floating 

IGx: On-Off, Floating 

GGx: DC 0(2) to 10 V or DC 0(4) to 20 mA proportional 

Input Signal 

AGx and IGx: AC 20 to 30 V at 50/60 Hz 

GGx: DC 0 to 10 V or DC 0(4) to 20 mA 

Input Signal Adjustments: 

AGx and IGx: CW and COM Terminals, CW rotation; CCW and COM Terminals, CCW rotation 

GGx (Voltage Input or Current Input): 

Jumper Selectable: DC 0(2) to 10 V or DC 0(4) to 20 mA 

Factory Setting: DC 0 to 10 V, CW rotation with signal increase 

Action is jumper selectable Direct (CW) or Reverse (CCW) with signal increase. 

Input Impedance 

AGx: 200 ohms, nominal 

IGx: 160 ohms, nominal 

GGx: Voltage Input, 150,000 ohms; Current Input, 500 ohms 

Feedback Signal 

AGF: 10,000 ohm potentiometer, 1 W 

GGx: DC 0 to 10 V or DC 2 to 10 V for 90° (1 mA); 

Corresponds to input signal span selection 

Auxiliary Switch Rating 

xGC: Two Single-Pole, Double-Throw (SPDT) switches rated at AC 24 V, 1.5 A inductive, 3.0 A resistive, 35 VA 

maximum per switch, Class 2 

Torque Rating 

1, 1.5, and 2 min. settings: 53 lb·in (6 N·m) 

5.5 and 11 min. settings: 35 lb·in (4 N·m) 

Cycle Life 

100,000 full cycles; 2,500,000 repositions rated at 53 lb·in (6 N·m) 

Audible Noise Rating 35 dBA maximum at 39.4 in. (1 m) 

Rotation Range 

Adjustable from 30 to 90°, CW or CCW 

Rotation Time 

IGx: Adjustable with switch settings (factory set for 1 min.) 60, 90, 120, 330, or 660 sec (1, 1.5, 2, 5.5 or 11 min.) 

at 60 Hz and 72, 108, 144, 396, or 792 sec at 50 Hz 

All Other Models: Nominal 60 seconds at 60 Hz and 72 seconds at 50 Hz for 90° 

Electrical Connection 

1/4 in. spade terminals (To order optional pluggable terminal blocks, see Accessories for M9106-xGx-2 Actuators.) 

Mechanical Connection 

3/8 to 1/2 in. (10 to 12.7 mm) round shaft or 3/8 in. (10 mm) square shaft 

Enclosure Rating 

NEMA 2, IP32 

Ambient Operating Rating 

-4 to 125°F (-20 to 52°C); 90% RH maximum, noncondensing 

Ambient Storage Rating 

IGx: -40 to 186°F (-40 to 86°C); 90% RH maximum, noncondensing 

All Other Models: -40 to 176°F (-40 to 80°C); 90% RH maximum, noncondensing 

Shipping Weight 

2.4 lb (1.08 kg) 

Compliance United States UL 873 Listed, File E27734, CCN XAPX 

Canada CSA C22.2 No. 139 Certified, File LR85083, Class 3221 02 

Europe CE Mark - Johnson Controls, Inc., declares that this product is in compliance with the essential requirements and 

other relevant provisions of the EMC Directive 2004/108/EC. 




3

M9106-xGx-2 Series Electric Non-Spring Return Actuators Catalog ...

Create successful ePaper yourself

Delete template?

Save as template?