Configurator primergy rx300 s7 - fujitsu global

PRIMERGY RX300 S7 

System configurator and order-information guide 

Contents 

March 2013 

Instructions 

Configuration diagram 

Configurator 

0 System software 

I Basic unit 

II Processor 

III Memory 

IV Graphics 

V Accessible drives 

VI Hard disk drives 

VII PCI Controller 

VIII Communication/Network 

IX System Management Products (RemoteView) 

X Miscellaneous 

XI Country specific power cord 

Change report 

PRIMERGY Server

Instructions 


PRIMERGY RX300 S7 Status 2013-02-28 

This document contains basic product and configuration information that will enable you to configure your system via 

PC-/System-Architect. 

Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete 

PRIMERGY Rack system. 

You can configure your individual PRIMERGY server in order to adjust your specific requirements. 

The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect. 

Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through 

the configurator by following the lines from the top to the bottom. 

X times 

Section III Memory, example 

S26361-XXX-XXX S26361-XXX-XXX 

Memory XXX MB Memory XXX MB 

max. X times per system max. X times per system 

There are X memory slots which can be equipped with XXX MB. 

It is permissible to make up to X passes through the memory upgrade options 

In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x 

Please note that there are information symbols which indicate necessary information. 

For further information see: 

http://ts.fujitsu.com/products/standard_servers/index.html (internet) 

https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx (extranet) 

Fujitsu Technology Solutions x86 PRIMERGY Serve 2 of 30

Configuration diagram PRIMERGY RX300 S7 

System unit ( I ) 

with up to 6x 3.5" Hard disk drives 

Key: 



Motherboard front side 

Memory CPU1 

( Channel A + B + C ) Bay for LocalView LCD 

Bank 1 (4 Modules) Xeon DP LSD 

Bank 2 (4 Modules) 2 USB 

Bank 3 (4 Modules) Air channel VGA, LAN 

Memory CPU2 Frontpanel 

( Channel D + E + F) Bay for 5,25"x 0,5" SATA-BR 

Bank 1 (4 Modules) Xeon DP or DVD-ROM/RW 

Bank 2 (4 Modules) 


Memory (III ) Processor ( II ) 

Accessible drives ( V ) 

rear side 

Fan 1 - Fan 5 

1. PSU 2. PSU Needs space for 2 

Redundant Fans 

are standard! 

hard disk drives! 

Redundant power 

supply option 

3.5"x1,6" 

Backup drive option 

Modular RAID Raid Card for IME, Raid 0 / 1E 

Support Raid Card for Raid 5 

Low-profile extension slots for: 

SCSI Controller for backup( VII ) Hard disk drives ( VI ) 

SAS Disk Array ( VIII ) 3.5" SAS/SATA 

Communication/Network ( IX ) 

Miscellaneous ( X ) 

3.5"x1" SAS or SATA 

Slot 6 PCIe-3 x16, 390mm @ CPU2 



Slot 4 PCIe-3 x8, max. 390mm @ CPU1 3.5"x1" SAS or SATA 

Possibility to install PCIe x16 cards 

Slot 3 PCIe-3 x8, max. 390mm @ CPU1 


Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored 

Dedicated for modular on-board LAN-Controller 



Slot 7 PCIe-3 x8, max. 168mm @ CPU1 3.5"x1" SAS or SATA 

Internal slot for modular RAID-Controller 

Included in basic unit Option 

One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit. 


Configuration diagram PRIMERGY RX300 S7 

System unit ( I ) 

with up to 4, 8, 12 or 16x 2.5" Hard disk drives 

Key: 



Motherboard front side 

Memory CPU1 

( Channel A + B + C ) Bay for LocalView LCD 

Bank 1 (4 Modules) Xeon DP LSD 

Bank 2 (4 Modules) 2 USB 

Bank 3 (4 Modules) Air channel VGA, LAN 

Memory CPU2 Frontpanel 

( Channel D + E + F) Bay for 5,25"x 0,5" SATA-BR 

Bank 1 (4 Modules) Xeon DP or DVD-ROM/RW 


Bank 3 (4 Modules) Accessible drives ( V ) 

Memory (III ) Processor ( II ) 

rear side Needs space for 4 

Fan 1 - Fan 5 2.5" hard disk drives! 

1. PSU 2. PSU 3.5"x1,6" 

Redundant Fans 

are standard! Backup drive option 1 

Redundant power 

supply option 

Needs space for 8 

2.5" hard disk drives! 

5.25"x1,6" 

Modular RAID Raid Card for IME, Raid 0 / 1E 

Support Raid Card for Raid 5 Backup drive option 2 

Low-profile extension slots for: 

SCSI Controller for backup( VII ) Hard disk drives ( VI ) 

SAS Disk Array ( VIII ) 2.5" SAS/SATA 

Communication/Network ( IX ) 

Miscellaneous ( X ) Up to 4 blocks with 4 HDDs 




Possibility to install PCIe x16 cards 



Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored 

Dedicated for modular on-board LAN-Controller 


Internal slot for modular RAID-Controller 

Included in basic unit Option 

2.5" SAS or SATA 








One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit. 


PRIMERGY-Software Configurators and Release Lists 

Start PRIMERGY RX300 S7 PRIMERGY RX300 S7 Status 2013-02-28 

SW Configurator 32 bit 

with OEM-Software without OEM-Software 

for PRIMERGY Server for PRIMERGY Server 

OEM- SW is bound to HW and 

VMware-Software is not allowed to be ordered 

- VirtualCenter Management Server for any server released for Windows Server 2003 separately. 

- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems Exception: VMware SW 

- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way 

For all SW products please refer to the corresponding software configurator accessible via 

the Extranet under Configuration & Tools, -All configurations, -Software, URL see below. 

Linux - Software **) 

- Open Enterprise Server ***) 

- SuSE Linux ES (OEM): LO 

- Red Hat EL (OEM): LO 

Microsoft - Windows Server 2008 Server Licenses 

- Windows Server 2008 Enterprise 

- Windows Server 2008 Standard PRIMECLUSTER *) 

- Windows Server 2008 Foundation - Clustering 

- Windows Web Server 2008 - Load Balancing 

Microsoft - Windows Server 2008 Client Access Licenses SCO - Software: **) 

- Windows Server 2008 Device CAL - SCO OpenServer 

- Windows Server 2008 User CAL (only 1- and 2-way Tower servers) 

- Windows Server 2008 Remote Desktop Services Device CAL - SCO UnixWare (only 1-, 2, and 

- Windows Server 2008 Remote Desktop Services User CAL 4-way Tower and Rack servers) 

x10sure *) 

x10sure Control Nodes and Compute Nodes 

Windows Server 2003 Compute Nodes 

for PRIMERGY BX600, RX/TX 

MultiPath, Duplex Data Manager (DDM) 

W2K; W2K3 Linux (W-DDM) 

for PRIMERGY except all mono PY systems 

Details eg. version numbers are published 

on the page referred to 

Manageability Software: V**) *) Pay attention to the x10sure release and ordering information in the Extranet under 

- iRMC advanced Pack https://ts.fujitsu.com/x10sure 

- RemoteView Software 

- RemoteView Service Board 

- RemoteView Diagnosis *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under 

- RemoteDeploy https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx 

**) Pay attention to release and order information in PRINCE -> Operating System 

https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx 

Backup-Software / 

Application-Software: U 

- ARCserve ***) Supply over distribution or procurement from FSC VP BC Software 

- openSM2 

You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: 

Continue with PRIMERGY 

HW configurator 

for internal users: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx 

for partners: https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx 

Fujitsu Technology Solutions x86 PRIMERGY Server

PRIMERGY-Software Configurators and Release Lists 


SW Configurator 64 bit (EM64T / IA64) 

with OEM-Software without OEM-Software 

for PRIMERGY Server for PRIMERGY Server 

OEM- SW is bound to HW and 

For all SW products please refer to the corresponding is not allowed to be ordered 

software configurator accessible via the Extranet under separately. 

"Configuration & Tools, -All configurations, -Software, Exceptions: VMware SW, 

URL see below. Citrix XenServer 

VMware-Software 

- VirtualCenter Management Server for any server released for Windows Server 2003 

- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems 

- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way 

Citrix XenServer / Essentials for XenServer 

- XenCenter Management Server for any server released for Windows 2000/XP/Vista and Server 2003/2008 

- XenServer and Essentials for XenServer released for RX200S5, RX300S4/S5, RX600S4, BX620S4/S5, BX920S1 

Microsoft Hyper-V Server and System Center 

- Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2 

- Microsoft System Center Essentials Management Suite for any server released for Windows Server 2008 SP2 

- Microsoft Hyper-V Server 2008 R2 

Microsoft - Windows Server 2008 R2 Server Licenses Linux - Software *) **) 

- Windows HPC Server 2008 R2 Suite # Open Enterprise Server ***) 

- Windows Server 2008 R2 Datacenter only - SuSE Linux ES (OEM): LO 

- Windows Server 2008 R2 Enterprise EM64T - Red Hat EL (OEM): LO 

- Windows Server 2008 R2 Standard 

- Windows Web Server 2008 R2 

Microsoft - Windows Server 2008 Server Licenses 

- Windows Server 2008 Datacenter PRIMECLUSTER *) 

- Windows Server 2008 Enterprise - Clustering 

- Windows Server 2008 Standard - Load Balancing 

- Windows Web Server 2008 

Microsoft - Windows Server 2008 Client Access Licenses QuickTransit (QT) 

- Windows Server 2008 Device CAL only Transition Solaris Apps. 

- Windows Server 2008 User CAL EM64T to x86-64 PY with Linux 

- Windows Server 2008 Remote Desktop Services Device CAL 

- Windows Server 2008 Remote Desktop Services User CAL 

only MultiPath, Duplex Data 

EM64T Manager (DDM) 

Windows, Linux (W-DDM) Details eg. version numbers are published 

on the page referred to 

*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under 

Manageability Software: V**) https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx 

- iRMC advanced Pack 

only - RemoteView Software 

EM64T - RemoteView Service Board **) Pay attention to release and order information in PRINCE -> Operating System 

- RemoteView Diagnosis https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx 

- RemoteDeploy 

***) Supply over distribution or procurement from FSC VP BC Software 

You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: 

Continue with PRIMERGY 

HW configurator 

for internal users: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx 

for partners: https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx 

Fujitsu Technology Solutions x86 PRIMERGY Server



Section I Basic unit 

A 

System unit consisting of: 

* 2U Housing without power supply modules 

* Basic units with: 

- 2 Hot-Plug Power Supply Bays 

- 5 Fans (full redundancy) 

* SAS Backplane for 6x 3.5" HD or SAS Backplanes for 4, 8, 12 or 16x 2.5" HD 

with cable connection to on-board or modular RAID Controller 

* Drives/Bays 

- 6 bays 1" for hot plug 3.5" HD (1" high) or 4, 8, 12 or 16 bays for hot plug 2.5" HD 

- 1 bay for 3.5" and 1.6" high Backup device, consumes 2 bays for 3.5" HD for basic unit 6x 3.5" HD 

not possible for basic unit with 12 or 16 x 2,5" HD 

- 1 bay for 5.25" and 1.6" high Backup device, not possible for basic unit 6x 3.5" HD 

for basic unit with 12 or 16 x 2,5" HD 

- 1 bay SATA-CD- or DVD-ROM 0,5" height (option) 

- 1 bay for opt. LocalView LC-Display 

* Integrated ServerView Diagnostics Technology ( Diagnosis LED`s ) for indication of internal 

failed components 

Systemboard D2939 with: 

* Up to two Xeon 4C, 6C & 8C CPU`s (Socket-R) 

with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU 

First CPU has to be selected for an orderable basic unit, 

* Chipset Intel® C600 Series (codenamed Patsburg) 

* 7 PCI slots: - 2x PCIe-3 x16 (both slots are connected to CPU 2 and are useable with configured 2nd CPU only!) 

- 4x PCIe-3 x8 (one notched to install x16 cards) 

- 1x PCIe-3 x8 (for internal modular RAID controller only) 

* 24 memory slots for max. 768GB RAM DDR3 available 

- Memory is divided into 12 DIMMs per CPU ( 4 channels with 3 slots per channel ) 

Possible max. configurations are: 

24x 32GB LRDIMM (quad rank modules) = 768GB 

24x 16GB RDIMM (dual rank modules) = 384GB 

16x 8GB UDIMM (dual rank modules) = 128GB 

First Memory ( one module ) has to be selected for an orderable basic unit per CPU 

- Memory upgrade is possible module wise 

- Memory mirrroring is supported with 2 identical modules in channel A+B CPU 1 or D+E CPU 2 

- Hot Spare Memory is supported with 3 identical modules in channel A+B+C CPU 1 or D+E+F CPU 2 

- SDDC (Chipkill) is supported for memory modules, 

* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board 

* iRMC S3 (integrated Remote Management Controller) on-board server management controller with 

dedicated 10/100/1000 Service LAN-port and integrated graphics controller. 

The Service LAN-port can be switched alternatively on standard Gbit LAN port 1 

* Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller): 

1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 

640x480x32bpp 85Hz 

(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off) 

Interfaces at the rear: 

* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared) 

* 1x VGA (15 pins) 

* 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup 

* 2x LAN RJ45, 1x Service-LAN RJ45 

Interfaces on the front: 

* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup 

* 1x VGA (15 pins) as an option 

* 1x Service-LAN RJ45 as an option 

Interfaces internal: 

* 1x released internal USB Interfaces for backup devices, 

* 1x USB 2.0 (UHCI) with 480MBit/s for dongle funcionality (uSSD memory), no USB wakeup 

* 1x SATA interface for DVD (only usable with 4x 2.5" HDD + DVD Option) 

* 4x SATA/SAS interface for 4 SATA/SAS HD`s or SAS Backup device 

* 2x USB 2.0 ports for internal USB redirection connected to BMC 

Software: 

* ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates 

* Documentation engl. (multilingual on CD) 


Rack version for 19'' racks with 


A PRIMERGY RX300 S7 Status 2013-02-28 

Cables included in basic unit 

Connections Cable PRIMERGY RX300 S7 

SAS 

1. SATA DVD SATA 

2. SAS cables to HDDs 

3. 1x cable for SAS signaling 

Note: Rack Mounting kit and Power Cord for RX300S7 is not included in the basic unit and 

has to be configured separately 

No PSU included in Base Unit Basic unit with 2.5" HDD bays is modular expand- 

Basic unit is without CPU and Memory able with various modules for backup devices 

For an orderable basic unit one CPU = first CPU and integration or up to 16x 2.5" HDDs. 

one memory = first memory has to be selected Details and pictures see Section Va: 

Basic unit with Possible configuration options for basic units 

6x 3.5" HDD bays fixed S26361-K1373-V101 

Basic unit with Full redundancy cannot be guaranteed for a max. 

2.5" HDD bays expandable S26361-K1373-V401 config. with e.g. two 135W CPUs with 450W PSUs. 

Basic unit with In this case SysArch will generate a warning and 

8x 2.5" HDD bays fixed S26361-K1373-V201 Power Safeguard will throttle CPUs 

Basic unit with in case of a PSU failure. 

12x 2.5" HDD bays fixed S26361-K1373-V301 So, power consumption will be limited to 450W. 

S26113-F575-E10 S26113-F574-E10 S26113-F609-E10 

450W PSU module platinum 800W PSU module platinum 800W PSU module -48V DC gold 

1st or 2nd PSU for redundancy 1st or 2nd PSU for redundancy 1st or 2nd PSU for redundancy 

94% efficiency (platinum) 94% efficiency (platinum) 92% efficiency (gold) 

uses hot plug PSU slot uses hot plug PSU slot uses hot plug PSU slot 

min. 1 / max. 2x per system min. 1 / max. 2x per system min. 1 / max. 2x per system 

B 

S26113-F574-E99 * For later redundancy upgrade the following kit is available: 

Power Supply Dummy One 450W power supply module hot plug S26113-F575-L10 

must be ordered if 1x PSU only no power cable included!!! 

occupies one bay for One 800W power supply module hot plug S26113-F574-L10 

hot plug power supply no power cable included!!! 

max. 1x per system One 800W -48V DC PSU hot plug S26113-F609-L10 

no power cable included!!! 

Please order appropriate power cord additionally: 

*For order completeness only Powercord for rack, 4m, grey, IEC320 C13->C14 connector T26139-Y1968-L10 

Not shown in system architect Power Cord USA / Canada, 1.8m, grey T26139-Y1742-L10 

Version > V9.2 Power Cord -48V DC, 4m, black T26139-Y4024-L10 

S26361-F3552-E1 

TPM Module 

Trusted Platform Module on Motherboard 

Use according to import restrictions S26361-F3552-L1 

max. 1x per system TPM Module add-on kit 

for later integration (loose delivery) 

Trusted Platform Module on Motherboard 

Be aware of import restrictions! Use according to import restrictions 

Loose delivery for later max. 1x per system 

integration possible for customer. 



B PRIMERGY RX300 S7 Status 2013-02-28 

PRIMECENTER Rack 

S26361-F2735-E145 S26361-F2735-E175 S26361-F2735-E111 Further information for 

RMK-F1_DI_CMA_QRL Rack Mount Kit F1-C S7 LV No Rackmount-Kit option rack mounting is available 

best choice for PrimeCenter racks best choice for 3rd party racks Only for loose deliveries within the 

consisting of consisting of No mounting in racks possible Corporate Partner Portal 

vario carrier 714-785mm vario carrier 559-914mm max. 1x per system 

telescopic drop-in rails 781mm telescopic drop-in rails 781mm All "L" no's for loose delivery 

with quick release lever support with quick release lever support 

with full extraction with full extraction S26361-F2735-L10 

with CMA adapter with CMA adapter Adapter angle PC/DC-Rack, till 50Kg 

1x per system 1x per system C necessary for mounting RMKs in 

asymmetrical PC racks 

S26361-F2735-L145 

RMK-F1_DI_CMA_QRL 

S26361-F4530-E11 S26361-F4530-E10 best choice for PrimeCenter racks 

Mounting 1U or 2U server in Mounting server in with CMA adapter 

asymmetrical racks symmetrical racks 

with 1U support bracket no support bracket needed S26361-F2735-L175 

RMK-F1_DI_CMA_QRL_LV 

best choice for 3rd party racks 

S26361-F2735-E71 S26361-F2735-E82 with CMA adapter 

Lateral cable management Rack Cable Management Arm CMA 2U 

for 2U servers or higher for 2U Server in racks S26361-F2735-L176 

- for asymmetrical racks - for symmetrical racks RMK-F1_DI_QRL_LV 

PRIMECENTER S2 or M1 M1 or 3rd party racks best choice for 3rd party racks 

- 1 bracket PC Rack asym. Fujitsu racks w/o CMA adapter 

1x per system 1x per system 

S26361-F2735-L7 

Lateral cable management (optionally) 

can only be mounted 

SNP:SY-F1647E301-P in asymmetrical PRIMECENTER 

Installation ex works for one S2 or new M1 racks in 1U above RMK 

server or subsystem. 

Hereby the rack will be delivered S26361-F2735-L82 

completely pre-mounted and Rack Cable Management Arm CMA 2U 

all wired connections are tested. for 2U Server in racks. 

With PCR M1 16U, 24U, 42U: 

Systems and components S26361-F2201-L20 

will be delivered installed in the rack Cable arm 2U PCR M1 S and 3rd p.-racks 

"Rack-mounting ex factory" for L176, has to be mounted above RMK 

This service is to be ordered once 

per installable server/storage 

subsystem, in order to get the 

To be ordered only together with server/storage subsystem 

a PRIMECENTER rack mounted into the racks. 

PCR S2 e.g. S26361-K826-V10x In case of not-installed server and subsystems 

new PCR M1 e.g. S26361-K827-Vxxx this service has to be ordered, 

refer PCR S2 or M1 rack configurator to get the mounting kits and the 

max. 1x per System cables installed. 

C 

PRIMERGY Classic 19" rack is not supported 


C 

Section II Processor 

There are 2 processor sockets available. 

The first socket must always be equipped with the first CPU which can be selected via configurator 

It is also possible to upgrade a dual-processor system later on with a second CPU 

Both PCIe-3 x16 slots are connected to CPU 2 and are useable with configured 2nd CPU only! 

Two processors with different clock frequencies are not possible 

A multi-processor operating system is required for a dual-processor system. 



Max. two CPU`s can be selected per basic unit Note: Max. DDR3 Bus Speed depends on: 

One of following CPU´s has to be selected as first CPU - max. DDR3 Bus Speed from the CPU and 

for an orderable basic unit - max. DDR3 Memory Speed and 

Optional second CPU has to be the same type like the first CPU - max. memory modules on one memory channel 

Basic 4C CPU's 

- 1x 64-bit Intel Xeon (10MB Smart Cache) 

1066 MHz DDR3 Bus; 6,40 GT/s QPI Bus and passive heat sink 

occupies socket for one CPU 

Xeon E5-2603 4C/4T 1.80GHz 10MB 6.40GT/s 1066MHz 80W S26361-F3685-E180 


Standard Turbo 6C CPU's 

- 1x 64-bit Intel Xeon (15MB Smart Cache); Hyper-Threading (HT); 






Advanced Turbo+ 8C CPU`s 

- 1x 64-bit Intel Xeon (20MB Smart Cache); Hyper-Threading (HT); 





Xeon E5-2665 8C/16T 2.40GHz 20MB 8.00GT/s 1600MHz 115W S26361-F3686-E240 On special release only 




Frequency Optimized Turbo 2C, 4C & 6C CPU`s 

- 1x 64-bit Intel Xeon (5/10/15MB Smart Cache); Hyper-Threading (HT); 

1600 MHz DDR3 Bus; 6,40/7,20 GT/s QPI Bus and passive heat sink 





Low Power 4C/6C/8C CPU's 

- 1x 64-bit Intel Xeon (15/20MB Smart Cache); Hyper-Threading (HT); 

1333/1600 MHz DDR3 Bus; 7,20/8,00 GT/s QPI Bus and passive heat sink 


Xeon E5-2630L 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 60W S26361-F3688-E200 

Xeon E5-2650L 8C/16T 1.80GHz 20MB 8.00GT/s 1600MHz 70W S26361-F3688-E180 

D 


D 

Section IV Graphics 



Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller): 

1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz 

(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off) 

S26361-F2571-E26 

Optional Front-VGA 

for Onboard Controller only 

consists of internal cable and 

front VGA connector 

max. 1x per system 

The hight end optional NVIDIA NVS300 graphic card offers dual head operation and fully 3D video support. 

The cables for either two times DVI-I or VGA (cable kit) connections are part of the delievery. 

Remote Video direction via iRMC must be disabled. 

This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot. 

max. 1x Only one card per server is allowed. 

E 

S26361-F2748-E637 

PY VGA LP card 256MB PCI-e x1 

NVIDIA NVS300 

512 MB PCIe-x1 PY VGA card must be installed in slot 4 (x8 wired x8) 

Connectors: 1x LFH 59 

cable kit for 2x DVI or 2x VGA 

cable kits included 

Dual head + professional 2-D + 3-D 

supported for Windows OS 

native driver support for Linux OS S26361-F2748-L637 

low profile bracket PY VGA LP card 512MB PCI-e x1 

max. 1x per system for loose delivery 



E PRIMERGY RX300 S7 Status 2013-02-28 

Section III Memory 

F 

- There are 12 memory slots per CPU for max. 

384GB LRDIMM (12x 32GB 4R) 

192GB RDIMM (12x 16GB 2R) 

32GB UDIMM (8x 4GB) 

=> max. 768GB for two CPU`s ( 384GB per CPU ), using LRDIMM 

- The memory area is divided into 4 channels per CPU with 3 slots per channel 

- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2, 

slot 3 belongs to memory bank 3 

Registered, LR DIMMs and unbuffered memory modules can be selected 

No mix of registered, load reduced and unbuffered modules allowed. 

Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type. 

Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed). 

In a 2 DIMMs per channel configuration, following frequencies are supported: 

- 1.5V - 1600MHz max (depending on CPU, special memory modules) 

- 1.35V - 1333MHz max (depending on CPU) 

In a 3 DIMMs per channel configuration, memory will operate at 1.5V only. 

SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only 

1.) In the "Independent Channel Mode" is following configuration possible 

Channels can be populated in any order in Independent Channel Mode. All four 

channels may be populated in any order and have no matching requirements. All 

channels must run at the same interface frequency but individual channels may run at 

different DIMM timings (RAS latency, CAS latency, and so forth) 

No mix of registered, load reduced and unbuffered modules allowed. 

2.) "Rank Sparing Mode" configuration 

- Within a memory channel, one rank is a spare of the other ranks. 

The Spare Rank is held in reserve and is not available as system memory 

For the effective memory capacity, please refer to the spreadsheet below. 

The BIOS is set to the rank sparing setting. 

Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel 

This mode is not supported by unbuffered memory modules 

3.) "Performance Mode" configuration 

- In this configuration, the memory module population ex factory is spread across all channels. 

The BIOS is set to the max. performance for memory. 

Minimum configuration is: 4x identical modules 

4.) In the "Mirrored Channel Mode" is following configuration possible 

- Each memory bank can optionally be equipped with 4x registered or load reduced or unbuffered DDR3 modules 

In each memory bank channel A and B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be 

equipped with identical modules for mirrored channel mode. 

In channel B / D is always the mirrored memory of channel A / B of CPU 1 

In channel F / H is always the mirrored memory of channel E / G of CPU 2 

Minimum configuration is: 4x identical modules 

This mode is not supported by unbuffered memory modules 

Fujitsu Technology Solutions x86 PRIMERGY Server 12 of 30


F PRIMERGY RX300 S7 Status 2013-02-28 

S26361-F3694-E10 Independent Mode 

Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined 

Requires min 1 memory Module per CPU 

S26361-F3694-E1 Rank Sparing Mode Installation 

BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shown in System Memory. 

For effective capacity within a channel, please have a look below. 

Supported for RDIMM / LRDIMM only. 

1x per CPU Requires min 2x 1R/2R or 1x 4R modules per CPU 

S26361-F3694-E2 Performance Mode Installation 

BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules 

will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used. 

Multiple of 4 identical modules to be configured per CPU 

S26361-F3694-E3 Mirrored Channel Mode Installation 

BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the 

Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data 

Supported for RDIMM / LRDIMM only. 

Multiple of 4 identical modules to be configured per CPU 

Effective Memory capacity / Rank Sparing Mode, 1 Channel populated 

UDIMM RDIMM LRDIMM 

2GB 1R 2GB 2R 4GB 1R 8GB 2R 16GB 2R 16GB 4R 32GB 4R 

1DPC na na na na na 12GB 24GB 

2DPC na na 4GB 12GB 24GB 28GB 56GB 

3DPC na na 8GB 20GB 40GB 40GB 80GB 

Minimum one memory module or order code per CPU = first memory 

Note 1.) 

Unbuffered Memory (UDIMM) no SDDC (chipkill) support Max. DDR3 memory speed depends on the memory configuration 

- one DDR3 unbuffered ECC mem. Module, 1.35V (No of mem modules per channe) as well as on the CPU type. 

Choose up to 8 order codes per CPU The memory channel with the lowest speed defines the speed 

2GB (1x2GB) 1Rx8 L DDR3-1600 U ECC S26361-F3694-E513 of all CPU channels in the system, also for the channels of the 

4GB (1x4GB) 2Rx8 L DDR3-1600 U ECC S26361-F3694-E514 second CPU if configured. 

Registered Memory (RDIMM) no SDDC (chipkill) support For real memory speed (depending on memory type / population), 

- one DDR3 registered ECC mem. Module, 1.35V please check the spreadsheet "Memory speed" below 

No mix with any other types of memory modules possible 

Choose up to 12x for 1R/2R or 8x for 4R per CPU 

For performance reasons, we do not recommend 

to configure more than 8 DIMMs per CPU 

4GB (1x4GB) 2Rx8 L DDR3-1600 R ECC S26361-F3695-E514 

Registered Memory (RDIMM) with SDDC (chipkill) support 

8/12x per - one DDR3 registered ECC mem. Module, 1.35V Mix of memory modules is only possible within the same group 

CPU, max. 1333MHz supported with up to 2DPC (8 modules/CPU) 

2/3 modules Choose up to 12 order codes per CPU 

per channel 4GB (1x4GB) 1Rx4 L DDR3-1333 R ECC S26361-F3696-E514 new due to supply 

8GB (1x8GB) 2Rx4 L DDR3-1333 R ECC S26361-F3696-E515 new due to supply 

Registered Memory (RDIMM) with SDDC (chipkill) support 

- one DDR3 registered ECC mem. Module, 1.35V 

1600MHz supported with up to 2DPC (8 modules/CPU) 

at 1.5V 

Choose up to 12 order codes per CPU 




Load Reduced Memory (LRDIMM) with SDDC (chipkill) support 

- one DDR3 load reduced ECC mem. Module, 1.35V 

Choose up to 12 order codes per CPU 

16GB (1x16GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E516 

32GB (1x32GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E517 

G 


Memory Configuration PRIMERGY RX300 S7 



Each CPU offers 12 Slots for DDR3 Memory Modules organised in 3 Banks and 4 Channels. 

If you need more than 12 Slots you have to configure the 2nd CPU. 

Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below). 

There are 3 different kinds of DDR3 Memory Modules available: UDIMM / RDIMM and LRDIMM 

UDIMM / RDIMM / LRDIMM offer different functionality. Mix of UDIMM / RDIMM / LRDIMM is not alloved. 

If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V 

Mode Configuration 

UDIMM RDIMM 

Application 

SDDC (chipkill) support any no no yes detect multi-bit errors 

Independant Channel 1, 2 or 3 Modules per Bank yes yes yes offers max. flexibility, upgradeability, capacity 

Mode use UDIMM modules for lowest cost 

Mirrored Channel Mode *) 4 identical Modules / Bank no no yes offers maximum security 

Performance Mode 4 identical Modules / Bank yes yes yes offers maximum performance and capacity 

Rank Sparing Mode *) min. 2 Ranks / Channel no no yes balances security and capacity 

*) For the delivery ex works the system will be prepared with dedicated BIOS setting. 

RDIMM 

LRDIMM 

x8 x8 x4 

Capacity Configuration UDIMM RDIMM LRDIMM Notes 

Min. Memory per CPU 1 Module / CPU 1x2GB 1x4GB 1x 16GB with one CPU 

Max. Memory per CPU 8/12 Modules / CPU 8x4GB 12x16GB 12x 32GB with one CPU 

Max. Memory per System 16/24 Modules / System 64GB 384GB 768GB if second CPU is configured 

Memory-Speed: 

Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU 

The memory channel with the lowest speed defines the speed of all CPU channels in the system 

Mem. Speed provided 

by CPU 

Voltage setting (BIOS) 

CPU with 1600MHz DDR3 Bus 



1R - Single Rank 

2R - Dual Rank 

4R - Quad Rank 

1DPC = 1 DIMM per Channel 



Configuration hints: 

- The memory sockets on the systemboard offer a color coding: 

Bank I black sockets 

Bank II blue sockets 

Bank III green sockets 

Real maximum memory-bus speed depending on CPU type, memory configuration (DPC) 

and voltage setting (BIOS) 

UDIMM 1600MHz RDIMM 1600MHz LRDIMM 1333MHz 

1.5V [default] 1.35V 1.5V [default] 1.35V 1.5V [default] 

1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 

DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC 

1333 

1333 

- 1066 

1066 

- 

1600 - 1333 - 

1333 1333 - 1066 1066 - 

1066 1066 - 1066 1066 - 

on special release 

as soon as available 

1600 1600 1066 1333 1333 

- 

- 

1333 1333 1066 

1333 1333 1066 1333 1333 - 

1066 1066 1066 1066 1066 

- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below) 

Bank I on CPU 1/2 up to 4 memory modules connected to Channel A - H on the 1st/2nd CPU 

Bank II on CPU 1/2 up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU 

Bank III on CPU 1/2 up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU 

(can not be populated by UDIMM or 4R RDIMM memory modules) 

- See below and next page for a detailed descriptions of the memory configuration supported. 

1 

1.35V 

2 3 

1066 

1066 

1333 1333 1066 1066 1066 - 

- 1066 1066 1066 1066 1066 - 

Fujitsu Technology Solutions x86 PRIMERGY Server 14 of 30 

- 

-

1. Independent Channel Mode 

Channel A 



required 

required if 2nd CPU is configured 

Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU 

(black sockets) 

Bank II Data Data Data Data Data Data Data Data optional, any type 

(blue sockets) 

Bank III Data Data Data Data Data Data Data Data -------- not used 

(green sockets) 

Independent Channel Mode allows all channels to be populated in any order 

Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system 

2. Mirrored Channel Mode 

Channel A 

required 


Bank I Data Mirror Data Mirror Data Mirror Data Mirror optional, same type in Bank per CPU 


Bank II Data Mirror Data Mirror Data Mirror Data Mirror -------- not used 


Bank III Data Mirror Data Mirror Data Mirror Data Mirror 


Mirrored Channel Mode requires identical modules on channel A,B, C, D (1st CPU) or channel E, F, G and H (2nd CPU) 

50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory 

If this mode is used, a multiple of 4 identical modules has to be ordered. 

3. Performance Channel Mode 

Channel A 

Channel B 

1st XEON CPU 

(4/6/8 Core) 

Channel B 

1st XEON CPU 

(4/6/8 Core) 

Channel B 

required 


Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU 


Bank II Data Data Data Data Data Data Data Data optional, any type 




1st XEON CPU 

(4/6/8 Core) 

Channel C 

Channel C 

Channel C 

Channel D 

Channel D 

Channel D 

2nd XEON CPU 

(4/6/8) Core) 

2nd XEON CPU 

(4/6/8) Core) 

Performance Channel Mode requires identical modules on all channels of each Bank per CPU. 

If this mode is used, a multiple of 4 identical modules has to be ordered. 

Channel E 

Channel E 

Channel E 

Channel F 

2nd XEON CPU 

(4/6/8 Core) 

Channel F 

Channel F 

Channel G 

Channel G 

Channel G 

Channel H 

Channel H 

Channel H 


4. Rank Sparing Mode 

Channel A 



required 


Bank I Spare Spare Spare Spare Spare Spare Spare Spare optional, same type in Channel per CPU 


Bank II 


Data Data Data Data Data Data Data Data optional, any type 



Channel A 

Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare required 

(black) R2 Data Data Data Data Data Data Data Data 


Bank II R1 Data Data Data Data Data Data Data Data 

(blue) R2 Data Data Data Data Data Data Data Data optional, same type in Channel per CPU 

Bank III R1 Data Data Data Data Data Data Data Data optional, any type 

(green) R2 Data Data Data Data Data Data Data Data 

-------- not used 

Channel A 

Channel B 

1st XEON CPU 

(4/6/8 Core) 

Channel B 

1st XEON CPU 

(4/6/8 Core) 

Channel B 

Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare required 

(black) R2 Data Data Data Data Data Data Data Data 

R3 Data Data Data Data Data Data Data Data required if 2nd CPU is configured 

R4 Data Data Data Data Data Data Data Data 

optional, same type in Channel per CPU 

Bank II R1 Data Data Data Data Data Data Data Data 

(blue) R2 Data Data Data Data Data Data Data Data optional, any type 


R4 Data Data Data Data Data Data Data Data -------- not used 

Bank III R1 Data Data Data Data Data Data Data Data 

(green) R2 Data Data Data Data Data Data Data Data 



1st XEON CPU 

(4/6/8 Core) 

Channel C 

Channel C 

Channel C 

1-Rank Memory modules (RDIMM) 

Channel D 

Channel D 

Channel F Channel F 

2nd XEON CPU 

(4/6/8) Core) 

4-Rank Memory modules (LRDIMM) 

Channel D 

Channel E 

Channel E 

Channel E 

2nd XEON CPU 

(4/6/8) Core) 

2-Rank Memory modules (RDIMM) 

Channel F 

2nd XEON CPU 

(4/6/8) Core) 

Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel. 

The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above 

"Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max. 

available memory, e.g. 6 DIMMs will be spread across two channels, each with 3DPC 

Channel G 

Channel G 

Channel G 

Channel H 

Channel H 

Channel H 



G PRIMERGY RX300 S7 Status 2013-02-28 

Section Va Possible configuration options for basic units 

H 

Config 1: 6x or 4x 3.5” HDD + 3.5" DDS/RDX drive 

Is fixed due to selection of basic unit with: 

6x 3,5" HDD bays fixed S26361-K1373-V101 

Basic unit S26361-K1373-V401 with expandable 

Config 2: 4x 2.5” HDD S26361-F1373-E420 *) 

Available Upgrade kits for this configuration option: 

Upgrade kit to 8x 2.5" HDD S26361-F1373-L424 


Upgrade kit to 4x 2.5" HDD + LTO S26361-F1373-L423 


Config 3: 4x 2.5” HDD + LTO S26361-F1373-E430 

Available Upgrade kits for this configuration option: 


Basic unit S26361-K1373-V201 with 

Config. 4: 8x 2,5" HDD bays fixed S26361-K1373-V201 

Available Upgrade kits for this fixed configuration: 




Config 5: 8x 2.5“ HDD + 3.5“ drive S26361-F1373-E450 

No Upgrade kit available! 


Config 6: 8x 2.5” HDD + LTO S26361-F1373-E460 

no ODD and LSD bay available! 


Basic unit S26361-K1373-V301 with 

Config 7: 12x 2,5" HDD bays fixed S26361-K1373-V301 

Available Upgrade kits for this fixed configuration: 



Config 8: 16x 2.5” HDD S26361-F1373-E480 

no ODD and LSD bay available! 


Includes all necessary bezels, cages, backplanes and cables 

*) this is the only one noHDD configuration opportunity without needed RAID controller 


H 

Section Vb Accessible drives 

Setup RX300 S7 by ServerStart is supported with following configurations: 

no DVD, no CD: 

remote installation only ( PXE service & DHCP server required) 

built in CD/DVD or USB CD/DVD disk drive: 

UNC Network share reachable or USB Floppy connected 

USB Floppy, no CD/DVD: 

USB CD/DVD connected 

If installation is done locally, make sure you have 

external FDD available for driver installation. 

Following USB Components are available 



1) USB DVD SM / Blu-Ray 

External SuperMulti Drive S26341-F103-L126 

External Blu-Ray Drive S26341-F103-L127 

2) USB Memorybird: 

MyUSBS A910 8GB, MLC Flash S26391-F6048-L208 

MyUSBS A910 16GB, MLC Flash S26391-F6048-L216 

S26361-F3269-E2 S26361-F3641-E2 

DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA 

all formats, DUAL/DL, DVD-RAM 6x BD-RW, 8x DVD, 24x CD 

1x BD DL and all CD/DVD formats 

1x 

H 

0.5 x 5.25", black bezel 0.5 x 5.25" 

max. 1x per system max. 1x per system 

as long as available 

S26361-F3324-E7 S26361-F3857-E7 Only for basic unit 

Tape drive DDS Gen5 USB 3.5" RDX drive USB 3.5" internal V1xx 

36GB, 3MB/s, USB 2.0 80-320GB, 25MB/s, USB 2.0 

1.6 x 3.5", black bezel 1.6 x 3.5", black bezel 

within a tape cage within a tape cage 

incl. description (Ger/US) incl. description (Ger/US) 

cleaning cartridge without RDX cartridges 

occupies 2 x 1" hard disk bays occupies 2 x 1" hard disk bays 


S26361-F3324-E5 S26361-F3325-E2 S26361-F3857-E5 

as long as available 

Tape drive DDS Gen5 USB 3.5" Tape drive DDS Gen6 USB 3.5" RDX drive USB 3.5" internal 

36GB, 3MB/s, USB 2.0 80GB, 6MB/s, USB 2.0 80-320GB, 25MB/s, USB 2.0 Only for basic unit 

Connector: USB "B" Connector: USB "B" Connector: USB "B" V4xx 

with USB cable with USB cable with USB cable 

incl. description (Ger/US) incl. cleaning cartridge incl. description (Ger/US) 

cleaning cartridge without data cartridge without RDX cartridges 

1.6 x 3.5", black bezel 1.6 * 3.5", black bezel 1.6 x 3.5", black bezel 

max. 1x per system max. 1x per system max. 1x per system 

USB 3.0 adapter & RDX 

S26361-F3749-E201 The adapter is also available as optional (loose) delivery 

USB3.0 PCIe x1 adapter card lp with FH and LP bracket included 

Sunrich U-720 S26361-F3749-L501 

PCIe x1 

1 port intern, 1 port extern 

USB 3.0 A jacks 


Only for basic unit Only for basic unit 

V4xx V1xx 

S26361-F3750-E5 S26361-F3750-E7 RDX cartridges must be ordered separately 

RDX Drive USB3.0 3.5" internal RDX Drive USB3.0 3.5" internal RDX 320GB = S26361-F3857-L320 

100MB/s, USB 3.0 100MB/s, USB 3.0 RDX 500GB = S26361-F3857-L500 

Connector: USB 3.0 "B" Connector: USB 3.0 "B" RDX 1TB = S26361-F3857-L600 

with USB cable within tape cage w/ USB cable 10x RDX320 = S26361-F3857-L329 

without RDX cartridges without RDX cartridges 

1.6 x 3.5", black bezel 1.6 x 3.5", black bezel The drive is also available as optional (loose) delivery 

max. 1x per system max. 1x per system S26361-F3750-L5/L7 with USB3.0 cable for adapter card. 

The USB3.0 Adapter card or the USB2.0 cable set 

S26361-F3750-L20 must be ordered with the drive! 


H 

SAS Controller for internal Backup Drives 

S26361-F3674-E1 For internal SAS Backup drives 

Onboard 4 port SAS Controller an additional 4-port SAS controller has to be configured 

LSI 

Patsburg B 

RAID 0, 1 & 10 

no controller cache 

SAS 1.0 (3Gb/sec) Only for basic unit 

4 internal ports V4xx 

PCIe x4 

no PCI slot required 


S26361-F3561-E4 S26361-F3626-E2 S26361-F3627-E1 



Tape drive LTO3HH Ultrium SAS Tape drive LTO4 HH SAS IBM V2 Tape drive LTO5HH Ultrium SAS 

400GB, 60MB/s, SAS 3Gb 800GB, 120MB/s, SAS 6Gb 1500GB, 140MB/s, SAS 6Gb 

Connector: mini-SAS Connector: mini-SAS Connector: mini-SAS 

1x incl. SAS cable incl. SAS cable incl. SAS cable 

incl. cleaning cartridge incl. cleaning cartridge incl. cleaning cartridge 

I 

without data cartridge without data cartridge without data cartridge 

1.6 * 5.25", black bezel 1.6 * 5.25" 1.6 * 5.25" 



I 

Section VI Hard disks drives 

Modular Raid controller is connected to internal HDDs 

For basic units V1xx up to 6 SAS 3.5" hard disks can be configured also in mixed configuration. 

If the option "Tape drive" is configured only 4 bays for hard disks are available 

Mixed configurations with Eco SATA drives and SAS drives are not allowed 



3.5" SAS drives and 3.5" BC SATA drives can be mixed, but not used in one logical RAID volume 

S26361-F4005-E530 S26361-F4005-E545 S26361-F4005-E560 

HD 300GB 15krpm 3.5" HD 450GB 15krpm 3.5" HD 600GB 15krpm 3.5" 

15.000rpm,

J 

S26361-F4581-E100 S26361-F4581-E200 S26361-F4581-E400 

SSD SAS 100GB, MLC SSD SAS 200GB, MLC SSD SAS 400GB, MLC 

Solid State Disk Solid State Disk Solid State Disk 

SAS 6Gb/s SAS 6Gb/s SAS 6Gb/s 

hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray 

max. 8/12/16x per system max. 8/12/16x per system max. 8/12/16x per system 

S26361-F5225-E100 S26361-F5225-E200 S26361-F5225-E400 

SSD SATA 100GB, MLC SSD SATA 200GB, MLC SSD SATA 400GB, MLC 

Solid State Disk Solid State Disk Solid State Disk 

SATA 6Gb/s SATA 6Gb/s SATA 6Gb/s 

Mainstream Perfomance Mainstream Perfomance Mainstream Perfomance 

hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray 

max. 8/12/16x per system max. 8/12/16x per system max. 8/12/16x per system 



S26361-F4541-E100 S26361-F4541-E400 

SSD 100GB, SLC SSD 400GB, SLC 

SAS 6Gb/s SAS 6Gb/s 

hot plug/hot replace tray hot plug/hot replace tray 

max. 8/12/16x per system max. 8/12/16x per system 

S26361-F3708-E250 S26361-F3708-E500 S26361-F3708-E100 No mix of 2.5" 

HD 250GB 7.2krpm 2.5" HD 500GB 7.2krpm 2.5" HD 1000GB 7.2krpm 2.5" BC-SATA/BC-SAS 

7200rpm,

1x 

K 



Section VII Modular Raid 0/1, Raid5 for SAS or SATA HD`s. On-board Controller for max. 4x 2.5" SATA or SAS HD`s 

L 

On board SATA Controller with 3 Gb/sec and up to 4x 2.5" SATA HDDs (no additional controller required) 

For up to 4x 2.5" SAS HDDs with RAID 0/1 functionality a Patsburg Upgrade Kit is required 

For all other HDD configurations a modular RAID-controller is required 

Following optional onboard SAS RAID can be selected for 4x2.5" HDDs or one SAS Tape device 

S26361-F3674-E1 

Onboard 4 port SAS Controller 

LSI 

Patsburg B 

RAID 0, 1 & 10 

no controller cache 

SAS 1.0 (3Gb/sec) 

4 internal ports 

PCIe x4 

no PCI slot required 


For more than 4 hard disks or 6 Gb/sec one of the following modular RAID-controllers is required 

Modular Raid 0/1 controller with IME support for SAS/SATA 

This RAID controller supports max. 8 HDDs on internal SAS ports 

Modular Raid 5 controller for SAS/SATA 

RAID levels 0, 1, 10, 5, 50, 6 and 60 The FBU is an option for the controller 

are supported. which can be used once per controller. 

This RAID controller supports max. 16 HDDs If the FBU option has been choosen, the 

combined with internal SAS expander TFM Module is needed once per FBU. 

S26361-F3554-E8 S26361-F3554-E512 S26361-F3669-E1 

RAID Ctrl SAS 6G 8port internal RAID Ctrl SAS 6G 8port internal RAID Ctrl SAS 6G 8port internal 

Based on chip LSISAS2008 Based on chip LSISAS2108 Based on chip LSISAS2208 

LSI MegaRAID LSI MegaRAID LSI MegaRAID 

no Cache, no BBU 512MB Cache with ECC 1GB Cache with ECC 

RAID 0, 1 & 10 RAID 0, 1, 10, 5, 50, 6, 60 RAID 0, 1, 10, 5, 50, 6, 60 

Support for 3Gb/s and 6Gb/s optional BBU optional FBU 

SATA and SAS hard drives Support for 3Gb/s and 6Gb/s Support for 3Gb/s and 6Gb/s 

PCIe x8 SATA and SAS hard drives SATA and SAS hard drives 

Low-profile MD2 form factor PCIe x8 PCIe x8 

max. 1x per system Low-profile MD2 form factor Low-profile MD2 form factor 


S26361-F3257-E216 

Cache Battery Backup Unit 

with 16 cm cable set 

max. 1x per Controller 

S26361-F3669-L660 Lose delivery FBU option S26361-F3669-E100 

RAID Key FastPath TFM Module for FBU option 

License Activation Key S26361-F3669-L100 

for 1 Controller TFM Module for FBU option max. 1x per Controller 

S26361-F3669-L661 max. 1x per Controller 

RAID Key CacheCade 

License Activation Key S26361-F3669-L110 S26361-F3669-E125 

for 1 Controller Flash Backup Unit Flash Backup Unit 

with 25cm, 55cm, 70cm cable set with 25cm cable set 

max. 1x per Controller max. 1x per Controller 



L PRIMERGY RX300 S7 Status 2013-02-28 

SAS-/SCSI-/ Fibre-Channel Controller Low Profile 

SAS controller for external backup drives 

No mix and match of different All controllers for the connection of external 

FC or FCoE controllers possible. storage system are delivered without cables. 

For the configuration of external cabling see 

the configurator for external storage system. 

Fibre Channel Controller for external storage systems 

For Fibre Channel SAN also other componets like 

S26361-F3631-E201 S26361-F3631-E202 switches, SFPs and optical wires are orderable 

8GBit/s FC Controller 8GBit/s FC Controller (for details see price liste) 

Qlogic Qlogic 

QLE2560, low profile bracket QLE2562, low profile bracket 

1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller loose delivery: 

LC Interface for 50µm Fiber LC Interface for 50µm Fiber Single channel S26361-F3961-L201 

PCIe x8, 170mm PCIe x8, 170mm Dual Channel S26361-F3961-L202 

max. 4x per system max. 4x per system with mounted LP bracket 

S26361-F3961-E201 S26361-F3961-E202 

8GBit/s FC Controller 8GBit/s FC Controller 

6x Emulex Emulex 

M 

S26361-F3628-E201 

SAS Controller 6Gb/s 8 port LP 

LSI SAS9200-8e LP 

PCIe 2.0 x4, 

ext: 8 port 


LPe1250, low profile bracket LPe12002, low profile bracket 

FH bracket is not included 

1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller loose delivery: 



max. 4x per system max. 4x per system with mounted LP bracket 

as soon as avaiable as soon as available 

S26361-F4994-E201 S26361-F4994-E202 

16GBit/s FC Controller 16GBit/s FC Controller 

Emulex Emulex 

LPe16000, low profile bracket LPe16002, low profile bracket 

FH bracket is not included 

1 channel 16GBit/sec FC Contr. 2 channel 16GBit/sec FC Contr. loose delivery: 



max. 6x per system max. 6x per system contains LP and FH brackets. 



M PRIMERGY RX300 S7 Status 2013-02-28 

N 

SAS RAID controller for JBOD subsystems 

S26361-F3593-E201 S26361-F3713-E201 

8 port SAS RAID Controller RAID Ctrl SAS 6G 8port external 

LSI LSI MegaRAID SAS 9285-8e 

MegaRAID SAS9280-8e 6Gb/s 1GB Cache with ECC 

512MB Cache with ECC RAID 0, 1, 5, 6, 10, 50 & 60 

RAID 0, 1, 10, 5, 50, 6 & 60 without FBU 

without iBBU SAS 6Gb/sec 

SAS 6Gb/sec 8 port external 

8 port external PCIe x8, MD2 form factor 

PCIe x4, 167mm low profile bracket 

low profile bracket max. 1x per system 


S26361-F3257-E216 BBU max. 2x per system possible 

Cache Battery Backup Unit for loose delivery please order S26361-F3669-E125 

with 16cm cable set S26361-F3257-L210 Flash Backup Unit 

max. 1x per Controller with 25cm cable set 

Lose delivery FBU option max. 1x per Controller 

S26361-F3669-L110 

Flash Backup Unit 

with 25, 55, 70 cable set 

max. 1x per Controller 



N PRIMERGY RX300 S7 Status 2013-02-28 

Section VIII Communication / Network 

1x 

N1 

2x Gigabit (Dualport) Ethernet Contr. Modular On-Board LAN is a flexible extension of a cost-optimized Motherboard 

onboard with basic 2x Gbit LAN on-board. 

Intel LAN I350 (Powerville) 3 different Upgrade-Kits are offered, which occupies a dedicated PCIe slot and 

ext: 2x RJ 45 connector can be ordered once per system. 

If a modular LAN Controller is installed, max. 3 additional LAN controllers are possible! 

Modular On-Board LAN Adapter 

S26361-F3740-E701 S26361-F3739-E701 S26361-F3629-E702 

Upgrade-Kit to 4x Gbit LAN on-board Upgrade-Kit to 6x Gbit LAN on-board Upgrade-Kit to 2xGbit+2x10Gbit LOM 

Eth Ctrl 2x1Gbit PCIe x4 D3035 Cu Eth Ctrl 4x1Gbit PCIe x4 D3045 Cu Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ 

Intel Powerville based 2 port Server Ad. Intel Powerville based 4 port Server Ad. Intel Niantic based dual port 10Gb NIC 

PCIe x4, Low Profile PCIe x4, Low Profile PCIe x8, Low Profile, Low Profile Bracket 

ext: for RJ45-plug, Cat 5 ext: for RJ45-plug, Cat 5 ext: 2x SFP+ cage 


while stock lasts 

S26361-F3611-E701 S26361-F3986-E3 

Upgrade-Kit to 6x Gbit LAN on-board SFP+ Module MMF 10GbE LC 

Eth Ctrl 4x1Gbit PCIe x4 D2745 Cu SFP+ module for 10 Gbit 

Intel Barton Hills based 4 Port Server Ad. Ethernet 50µm FO cabling 

PCIe x4, low profile ext:LC-connector 

ext: for RJ45-plug, Cat 5 max. 2x per adapter 


S26361-F3986-E4 

The 10Gb upgrade kit is delivered without SFP+ modules SFP+ Module SMF 10GbE LC 

for optical cables, these must be ordered separately. SFP+ module for 10 Gbit 

Without SFP+ modules copper twinax cables are supported Ethernet 9µm FO cabling 

ext:LC-connector 

The SFP+ Module is also available as loose delivery max. 2x per adapter 

S26361-F3986-L3 / L4 

Instead SFP+ Modules, SFP+ twinax cables from 

the switch vendors may be used S26361-F3629-E750 

For cabling of D2755 please refer to chapter Shared 10Gb Management LAN 

10GbE 2-Port SFP+ for MMF Module Install and configure Management 

LAN on 10Gb Shared LAN port 

This is an option if Shared Management LAN over the max. 1x per 10Gb upgrade kit 

10Gb port is required instead Management LAN over 1Gb 


N1 

A) 1-Port Copper PCIe Adapter 1000TX 

S26361-F3516-E201 

(Shelter Island) 

Gigabit Ethernet Controller 1000TX LP Loose delivery with: 

Eth Ctrl 1x1Gbit PCI-e Gigabit CT DT Cu LP S26361-F3516-L201 

Intel® Gigabit CT Desktop Adapter 

PCIe x1 

ext: for RJ45-connector, Cat 5 


B) 1-Port MMF PCIe Adapter 1000SX 

S26361-F3242-E201 

(Sheepshead Bay) 

Gigabit Ethernet Contr. 1000SX Loose delivery with: 

Eth Ctrl 1x1Gbit PCI-e Pro/1000PF LC S26361-F3242-L201 

Intel PRO/1000 PF Server Adapter 

PCIe x4 



C) 2-Port Copper PCIe Adapter 1000TX 



4x S26361-F3740-E201 

(D3035) 

Gigabit Ethernet Controller Dual 1000TX LP Loose delivery with 

Eth Ctrl 2x1Gbit Cu PCIe x4 D3035 lp FH and LP bracket included: 

Intel Powerville based 2 port Server Adapter S26361-F3740-L501 

PCIe x4, Low Profile 

low profile (LP) bracket 

ext: for RJ45-plug, Cat 5 


D) 4-Port Copper PCIe Adapter 1000TX 

while stock lasts 

S26361-F3739-E201 S26361-F3611-E201 

(D3045) (D2745) 

Gigabit Ethernet Controller Quad 1000TX LP Gigabit Ethernet Controller Quad 1000TX LP Loose delivery with 

Eth Ctrl 4x1Gbit Cu PCIe x4 D3045 lp Eth Ctrl 4x1Gbit PCIe x4 D2745 Cu lp FH and LP bracket included: 

Intel Powerville based 4 port Server Adapter Intel Barton Hills based 4 port Server Ad. S26361-F3739-L501 

PCIe x4, Low Profile PCIe x4, Low Profile 

low profile (LP) bracket low profile (LP) bracket Loose delivery with 

ext: for RJ45-plug, Cat 5 ext: for RJ45-plug, Cat 5 FH and LP bracket included: 

max. 4x per system max. 4x per system S26361-F3611-L501 

N2 


2x 

N2 

E) 10GbE 2-Port SFP+ for MMF Module 



S26361-F3629-E202 

(D2755) 

10 Gigabit Ethernet Contr. dual port SFP+ 

Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ The controller is delivered without SFP+ modules for optical cables, these must be 

Intel Niantic based dual port 10Gb NIC ordered separately. Without SFP+ modules copper twinax cables are supported. 

PCIe x8, Low Profile, Low Profile Bracket The adapter is also available as loose delivery with 

ext: 2x SFP+ cage FH and LP bracket included: S26361-F3629-L502 


S26361-F3986-E3 S26361-F3986-E4 The SFP+ Module is also available as loose delivery 

SFP+ Module MMF 10GbE LC SFP+ Module SMF 10GbE LC S26361-F3986-L3 

SFP+ module for 10 Gbit SFP+ module for 10 Gbit The SFP+ Module is also available as loose delivery 

Ethernet 50µm FO cabling Ethernet 9µm FO cabling S26361-F3986-L4 

ext:LC-SR-connector ext:LC-LR-connector Instead SFP+ Modules, SFP+ twinax cables from 

max. 2x per adapter max. 2x per adapter the switch vendors may be used 

V:TWX Connector-PY 

for all Twinax (FTS,BR,CI) 

max. 2x per controller 

S26361-F3989-E600 *) S26361-F3873-E500 *) S26361-F4571-E500 *) *) in SA only 

SFP+ active twinax cable SFP+ active twinax cable SFP+ passive twinax cable shown in 

customized twinax cable for customized twinax cable for customized twinax cable for cabling view 

full rack setup ex factory full rack setup ex factory full rack setup ex factory 

cable length is selected by cable length is selected by cable length is selected by 

requirement in the factory requirement in the factory requirement in the factory 

2x Fujitsu branded cable Brocade branded cable Cisco branded cable 

O 

max. 2x per controller max. 2x per controller max. 2x per controller 

F) 10GBASE-T 2-Port for 10Gb Eth. Over copper cable 

S26361-F3752-E202 The adapter is also available as loose delivery with 

Eth Ctrl 2x10GBase-T PCIe x8 X540-T2 lp FH and LP bracket included: S26361-F3752-L502 

Intel Twinville based 2 port Server Adapter 

PCIe x4, Low Profile 

low profile (LP) bracket 

ext: for RJ45-plug, Cat 6 


separate orderable 10Gb Ethernet cables 

S26361-F3989-L102 SFP+ active twinax cable 2m 






S26361-F4571-L101 SFP+ passive twinax cable 1m 






2x 

O 

F) Fibre Channel over Ethernet 



S26361-F3592-E202 Loose Delivery: S26361-F3592-L202 

10GBit/s CNA 

Emulex 

OCe10102 

2 channel 10GBit/sec CNA 

SFP+ Cage 

PCIe x8, 170mm 

max. 2 per system 

S26361-F3592-E108 The SFP+ Module is also available as loose delivery 

SFP+ Module MMF 10GbE LC S26361-F3592-L108 

SFP+ module for 10 Gbit Instead SFP+ Modules, SFP+ twinax cables from 

Ethernet FO cabling the switch vendors may be used 


max. 2x per adapter 

V:TWX Connector-PY 

for all Twinax (FTS,BR,CI) 

max. 2x per controller 

S26361-F3989-E600 *) S26361-F3873-E500 *) S26361-F4571-E500 *) *) in SA only 

SFP+ active twinax cable SFP+ active twinax cable SFP+ passive twinax cable shown in 

customized twinax cable for customized twinax cable for customized twinax cable for cabling view 

full rack setup ex factory full rack setup ex factory full rack setup ex factory 

cable length is selected by cable length is selected by cable length is selected by 

requirement in the factory requirement in the factory requirement in the factory 

Fujitsu branded cable Brocade branded cable Cisco branded cable 

max. 2x per controller max. 2x per controller max. 2x per controller 

G) Infiniband HCA's 

separate orderable 10Gb Ethernet cables 












S26361-F4475-E102/E202 loose delivery: S26361-F4475-L102/L203 

IB HCA 40Gb 1 and 2 port QDR 

IB HCA 1x / 2x 40Gb Low Profile PCIe form factor with 

PCIe 2.0 (5,0GT/s) exchangeable Full Height (FH) 

PCIe x8, low profile or Low Profile (LP) bracket 

ext: 1x / 2x QSFP-connector 


4x only within a rack If additional length of copper cable or 

configuration optical cable are needed, then they must 

2x 

P 

S26361-F3996-E500 be ordered from the cable vendor directly 

InfiniBand Cu Cable 40Gb Copper cable are also available for loose 

customized delivery as 

QSFP, 1m and 3m S26361-F3996-L101, QSFP, 40Gb, 1m 

max. 2x per adapter S26361-F3996-L103, QSFP, 40Gb, 3m 

For the US market only: 

Due to EMI restrictions, only one IB FDR HCA 

might be installed per system 

S26361-F4475-E103/E203 S26361-F4533-E102/E202 loose delivery: S26361-F4475-L103/L203 

IB HCA 40Gb 1 and 2 port QDR enhanced IB HCA 56Gb 1 and 2 port FDR loose delivery: S26361-F4533-L102/L202 

IB HCA 1x / 2x 40Gb IB HCA 2x 56Gb 

PCIe 3.0 (8,0GT/s) PCIe 3.0 (8,0GT/s) 

PCIe x8, low profile PCIe x16, low profile Low Profile PCIe form factor with 

ext: 1x / 2x QSFP-connector ext: 2x QSFP-connector exchangeable Full Height (FH) 

max. 2x per system max. 2x per system or Low Profile (LP) bracket 

only within a rack 

configuration 

S26361-F3996-E556 If additional length of copper cable or optical cable are needed, 

InfiniBand Cu Cable 56Gb then they must be ordered from the cable vendor directly 

customized Copper cable are also available for loose delivery as 

QSFP, 1m and 3m S26361-F3996-L561, QSFP, 56Gb, 1m 

max. 2x per adapter S26361-F3996-L563, QSFP, 56Gb, 3m 



P PRIMERGY RX300 S7 Status 2013-02-28 

Section IX System Management Products (RemoteView) 

iRMC S3 (integrated Remote Management Controller) onboard server management 

Controller with dedicated 10/100/1000 Service LAN-port and integrated graphics. 

Optional 10/100 Service LAN-port on front panel. 

The Service LAN-port can be switched alternatively on standard Gbit LAN port 

S26361-F1790-E242 

iRMC S3 advanced pack 

integrated remote management controller 

activation key for 

graphical console redirection 

and remote media redirection 


S26361-F2557-E106 

Local Service Display incl. mount. kit 

Customer Self Service 

LSD module incl. mounting kit 

0.5" x 5.25" 


S26361-F2571-E27 

Maintenance LAN 

Front management LAN Port 

In combination with iRMC adv. pack 

For local maintenance / console redirection, 

Integrated in front (operating panel) 


Section X Miscellaneous 

Options and other peripherals 

For other options, refer to SystemArchitect and Pricelist 

These options are supplied lose with the shipment 

For suitable peripherals for this product, please refer to SystemArcitect 

S26361-F3776-E1 Configuration restrictions in LNM for RX300: 

ENABLING LOW NOISE MODE RX300 Max 2x CPU with max 80W allowed! 

Restricts configuration to make Max 8x memory DIMMs allowed! 

LNM possible Modular RAID card only (S26361-F3554-E8/E512 or S26361-F3669-E1) 

LNM is enabled ex factory No other PCIe cards are allowed! 

max. 1x per system LNM can be enabled later, as long as the configuration restrictions are fulfilled 

Section XI Country specific power cord 

Power cord options (1x per PSU) 

T26139-Y1968-E100 Powercord for rack, 4m, grey, 

IEC 320 C14 connector 

max. 

2 x T26139-Y1742-E10 USA, Canada, 1.8m, grey 

S26361-F1452-E100 S26361-F1452-E110 

REGION KIT EMEA AP REGION KIT JP 

For Shipments to EMEA / Asia and For Shipments to Japan regions 

Pacific regions 

1x per system 1x per system 

Power cord has to be ordered separately 

T26139-Y4024-E10 for -48V DC PSU only, 4m, black 

T26139-Y3850-E10 Option "no powercord", for Countries without 

specific cable orderable like e.g. China 

End PRIMERGY RX300 S7 

When adding not compatible components later, LNM will be switched off automatically 


Date Order number Changes 

Change Report 



2013-01-29 S26361-F2735-E145 Add RMK-F1 Standard , tab basic unit 

2013-01-17 S26361-F3750-E7 RDX USB3.0 for basic Unit V1xx added 

2013-01-14 S26361-F3750-L20 Hint for "RDX Drive USB2.0 cable set" added 

2013-01-08 S26361-F5228-E*** New 2.5" BC SAS 7.2K HDD 

2013-01-08 S26361-F5247-E*** New 2.5" SAS 10K HDD (mix with BC-SATA supported, sucessor for *F5227*) 

2012-12-13 S26361-F3750-E7 RDX USB3.0 for V1xx removed 

2012-12-10 S26361-F3694-E3 as soon as available removed 

2012-12-07 S26361-F3776-E1 ENABLING LOW NOISE MODE RX300 added 

2012-11-22 F3749-E4 and F3750-E4 "as soon as available" removed 

2012-11-22 S26361-F3857-E4 "as long as available" added 

2012-10-08 S26361-F3749-Exx Added USB3.0 Adapter 

2012-10-08 S26361-F3750-Ex Added RDX Drive 

2012-10-01 S26361-F3986-E4 New SFP+ Module SMF 10GbE LC 

2012-10-01 S26361-F3740-E201/E701 New 4-port Intel LAN controller and upgrade kit - as soon as available 

2012-10-01 S26361-F3739-E201/E701 New 2-port Intel LAN controller and upgrade kit - as soon as available 

2012-09-28 S26361-F4541-E200 EOL: 200GB SSD SAS SLC 

2012-07-30 S26361-F2735-L176 Add RMK-F1 LV w/o. CMA adapter (short rail 731mm) 

2012-07-25 S26361-F4581-Exxx Add SSD SAS MLC 

S26361-F5225-Exxx Add SSD SATA MLC 

2012-07-16 S26361-F3857-L160/L169 RDX Cartridge 160GB is EOL => removed 

2012-07-13 S26361-F5227-E1* New order for 2.5” 10K SAS HDD supporting mix with 2.5” BC-SATA HDD 

2012-07-13 S26361-F3857-L160/L169 RDX 160GB Cartridge is EOL=> removed 

2012-06-12 S26361-F5225-E*00 New order for SATA SSD´s 

2012-06-05 S26361-F2735-E82 Configuration in asymmetrical racks released 

2012-04-23 S26361-F3713-E201 new RAID Controller added 

2012-04-20 Memory voltage / frequency spreadsheet, 3DPC at 1.5V only 

2012-02-29 First Release

Configurator primergy rx300 s7 - fujitsu global

Create successful ePaper yourself

Delete template?

Save as template?