Ideas on protocol format #3

netmindz · 2022-03-15T10:22:51Z

netmindz
Mar 15, 2022
Maintainer

Thought it might be easier to keep track of ideas/thoughts/theories/discoveries about the protocol here, rather than keep editing the wiki, potentially removing information that was correct before I went down a dead end

So, my current understanding can be summarised as follows:

There appears to be no single byte value that indicates the start of a new message, unlike the newer balboa systems
There appears to be at least two different message starts, FA and AE
Some of the FA messages contain the temp in C, along with the status of light, heater and pumps, others seem to have different data, but unsure what or how to differentiate yet - other than temp value not having the byte that shows temp C or -
When the temp is unknown you see --- on the panel and 2D 2D 2D 2D in the data, which is "----" as ASCII
The AE messages start AE0D0, then 0,1,2,3
You see the 3 messages for FA, then see the AE messages, e.g AE0D01, then FAs then AE0D02 ...etc
Every message is in a group of 3, the short form, then long form, then short again. e.g
I'm undecided if FB is the start of it's own message or not. Sending in groups of 3 like this feels odd, the FB could be a reply for the FA, but then why send the same FA again? As we also get FB after the AE messages, then not as simple as FB being reply to FA

fa142d2d2d2d0000040000008002ffffff000000000068
fa142d2d2d2d0000040000008002ffffff000000000068fb0603450e0000ff74
fa142d2d2d2d0000040000008002ffffff000000000068

ae0d03000000000000000000000000b4
ae0d03000000000000000000000000b4fb0603450e0000ff74
ae0d03000000000000000000000000b4

netmindz · 2022-03-15T10:30:27Z

netmindz
Mar 15, 2022
Maintainer Author

Further "proof" that FB is not start of new message is that there is no time delay between the previous bytes and the FB as seen in https://github.com/netmindz/balboa_GL_ML_spa_control/blob/main/tests/bggardner-timestamp-interval.log

0 replies

netmindz · 2022-03-16T08:28:55Z

netmindz
Mar 16, 2022
Maintainer Author

Whatever the FB sequence is, it can stay consistent for quite a while, even when things like the cleaning cycle runs. The FB sequence on the end of the FA messages is always the same as the ones for AE

1 reply

netmindz Jun 15, 2022
Maintainer Author

FB are created by the top panel and change only on key presses

netmindz · 2022-03-20T13:45:30Z

netmindz
Mar 20, 2022
Maintainer Author

Most of the the time the AE messages are all 0, then sometimes see other values for very short periods, possibly single message, e.g AE 0D 00 00 00 21 9A 08 80 B0 1F

Looks like I'm also seeing the same 21 9A 08 80 B0 1F on AE 0D 01 too

0 replies

netmindz · 2022-03-26T13:54:04Z

netmindz
Mar 26, 2022
Maintainer Author

The sequence after the FFFF is where information like temp+ and temp- are sent

fa143 .... 94600008002ffffff0200000000f5

0000000000
1000000000
0000000000
1000000000
1400000000
0000000000
0100000000 - temp up
0200000000 - temp down
0800000000

0 replies

netmindz · 2022-04-17T13:16:06Z

netmindz
Apr 17, 2022
Maintainer Author

I'm thinking more that FB are a message in their own right, but the lack of delay is that whichever end (panel vs control) is sending this the FA/AE and FB messages as a "pair" - hence the lack of delay

1 reply

netmindz Jun 14, 2022
Maintainer Author

The FB sequence is created by the top panel. If you unplug the top panel while running, you just see the short version of the message 3 times

netmindz · 2022-04-17T13:21:29Z

netmindz
Apr 17, 2022
Maintainer Author

That said, if you do consider them a message in their own right, then the ordering of the messages is even more bizzare as you get the same value twice, then an FB, then the value again

e.g

ae0d000000000000000000000000002d
ae0d000000000000000000000000002d
fb0603450e0000ff74
ae0d000000000000000000000000002d
fa14333735430000610000008002ffff63000000000007
fa14333735430000610000008002ffff63000000000007
fb0603450e0000ff74
fa14333735430000610000008002ffff63000000000007
ae0d010000000000000000000000005a
ae0d010000000000000000000000005a
fb0603450e0000ff74
ae0d010000000000000000000000005a
... etc for AE0D00 - AE0D03

2 replies

tmjo Apr 18, 2022
Collaborator

Could it be that the controller sends some kind of data and the panel is supposed to reply the same? Or some kind of handshake, perhaps a unique address for various panels or something?

netmindz Jun 15, 2022
Maintainer Author

The "placement" of the FB messages seems to relate to which port on the control board the top panel is connected - middle port means replied to the 2nd FA or AE message

netmindz · 2022-05-24T13:26:12Z

netmindz
May 24, 2022
Maintainer Author

The FA message contains the time, followed by the temp in Fahrenheit

0 replies

netmindz · 2022-09-24T11:26:42Z

netmindz
Sep 24, 2022
Maintainer Author

@tmjo Did you see #13 ?

3 replies

tmjo Sep 29, 2022
Collaborator

Hi! Sorry for my late replies. I've seen you've got something going on there, but I've been so loaded lately with work and at home, so I didn't have much time to study it. Does it seem to work well?

netmindz Oct 5, 2022
Maintainer Author

It did seem to be working well, had even progressed to the point I was able to toggle the light on and off if I spammed the bus with my FB message, but then suddenly was all over the place.

It coincided with when I moved from having it all pulled out to test Vs when pushed back away. As just in a breadboard at the moment, suspect loose write or I've put something back in the wrong place as with my initial read until low code, I was seeing perfect message "framing"

netmindz Oct 5, 2022
Maintainer Author

I've ordered another 8 pin connector as I suspect pin 5 goes low one port at a time to indicate when each panel is clear to send data

netmindz · 2022-10-09T15:30:02Z

netmindz
Oct 9, 2022
Maintainer Author

Pin 5 definitely goes low on each main panel port in turn - not 100% sure yet exactly when this sits relative the the messages

1 reply

tmjo Oct 11, 2022
Collaborator

That looks very promising!

netmindz · 2022-10-13T08:45:30Z

netmindz
Oct 13, 2022
Maintainer Author

So - Pin5 is used to control which panel is active at any given time, hence why the protocol sends a panel query command 3 time, once for each port. Only the panel who's pin5 is active will be expected to respond, the others just discard this data

1 reply

TiSiAi Mar 11, 2023

I haven't at house an memory oscilloscope , have you see when the data can be send from the panel ?
When the Pin5 I low or when the pin5 return to Hi ?

TiSiAi · 2023-03-04T22:37:35Z

TiSiAi
Mar 4, 2023

Hello
Very good Job
Im going to work on this projet and just buy an another Balboa ML700 to control the spa since indoor and in a second part I would replace the second keyboard with an ESP32 to control the SPA from iOS application.
Your project is very advanced. Thank a lot for share
If later I can help and participate ...
++

12 replies

netmindz Mar 16, 2023
Maintainer Author

Remind me @tmjo what is the model number of your top panel?

netmindz Mar 16, 2023
Maintainer Author

Hello @netmindz I receive my new top Panel used as second panel for debug the Pin 2 is used with my panel to turn on led on the back panel

So do you see that light flashing then? Is there any label or info in the manual for that panel that indicates it's purpose? Do you see the same odd pattern with your scope https://github.com/netmindz/balboa_GL_ML_spa_control/blob/main/scope/pin2/Screenshot%20from%202022-02-05%2012-59-59.png

TiSiAi Mar 16, 2023

I think they are 2 CRC
1 for the FA14 frame ( receive command from GL unit )
1 for the FB06 frame ( send command from the keyboard )
I just found ( I think ) the CRC for the send command ( the most useful )
based on the ccutrer/balboa_worldwide_app
I search on ( CS: Checksum (CRC-8 with 0x02 initial value, and 0x02 final XOR) )
with this info I search a code to generate et in found the code of : balboa_helper.ino
i modify some value with a generator to find a valid CRC with my sample of frame ( 4 sample )

{ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x00,0xFF};
{ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x04,0xFB};
{ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x02,0xFD};
{ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x01,0xFE};

and bingo
for the FB06 CRC the start value of the CRC is: 0xFB (251 in decimal )
the CRC function modified is ok for my 4 sample

this is the code modified

inline uint8_t crc8(uint8_t *data,uint8_t dataLength,uint8_t crcStart,uint8_t crcEnd)
{
  unsigned long crc;
  int i, bit;
  uint8_t length = dataLength;

  crc = crcStart;
  for ( i = 0 ; i < length ; i++ ) {
    crc ^= data[i];
    for ( bit = 0 ; bit < 8 ; bit++ ) {
      if ( (crc & 0x80) != 0 ) {
        crc <<= 1;
        crc ^= 0x7;
      }
      else {
        crc <<= 1;
      }
    }
  }
  return crc ^ crcEnd;
}

for use and validate:

uint8_t dataMemory1[] ={ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x00,0xFF};
uint8_t dataMemory2[] ={ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x04,0xFB};
uint8_t dataMemory3[] ={ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x02,0xFD};
uint8_t dataMemory4[] ={ 0xFB,0x06,0x64,0xD4,0x06,0x00,0x01,0xFE};

uint8_t crcStart=0xFB;
uint8_t crc_computed1 = crc8(dataMemory1,8,crcStart,0);
uint8_t crc_computed2 = crc8(dataMemory2,8,crcStart,0);
uint8_t crc_computed3 = crc8(dataMemory3,8,crcStart,0);
uint8_t crc_computed4 = crc8(dataMemory4,8,crcStart,0);

if((crc_computed1==0x40) && (crc_computed2==0x08) && (crc_computed3==0x64) && (crc_computed4==0x52) )
{
    Serial.println("Valid CRC");
}

TiSiAi Mar 16, 2023

So do you see that light flashing then? Is there any label or info in the manual for that panel that indicates it's purpose? Do you see the same odd pattern with your scope

The back of the panel has LED
The power is alternate 15V signal but with the frequency it is not visible

and the pin 2 signal ( dark blue )

netmindz Mar 16, 2023
Maintainer Author

Great work on the CRC.
I had planned to try the CRC code from other Balboa projects but combination of forgetting and I think one of them was in python meant I didn't fully follow up on that

tmjo · 2023-03-16T11:34:45Z

tmjo
Mar 16, 2023
Collaborator

@netmindz; Hi! First of all, sorry for my absence the latest months. I've been away and abroad for three months, and my tub have been empty. Now is the time to fill it up again, and spend some more time on this library. Really looking forward to being able to control the tub!

My top panel is ML400 with buttons for Jets, Aux, Temp and Light. Jets are toggling between off, speed1, speed2. Aux is similar (but my pump is broken). Temp is activated by pushing once, display is blinking, then pushing several times to either increase or decrease temperature (increasing on first entry, decreasing on second). Light is off and on, but also toggling between colours if pressing rapidly.

5 replies

netmindz Mar 16, 2023
Maintainer Author

Thanks for the info, no worry about being quiet. I just assumed you were happy with the current read-only status

netmindz Mar 16, 2023
Maintainer Author

It's super useful @TiSiAi has the Balboa ML700 as that's the most powerful of the three of us, so he should be able to help with doing things like setting the actual time of the tub that I can't do with mine, so I can then set the cleaning by actual time of day, not just based on twice daily based on when power was applied

TiSiAi Mar 16, 2023

Yes ;)

this is the frame with change routine
CLOCK
start filtration 1
end filtration 1
start filtration 2
end filtration 2

the brut frame analysing ( sorry the AE0D frame are formatted same FA14 )

Move the post if need, its so long
I put it here temporary


//Settings clock
20:48:29.359 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:29.426 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:29.492 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:29.524 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:29.589 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:29.688 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:29.720 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:29.785 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:29.850 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:29.915 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:29.981 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:30.047 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:30.112 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:30.145 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:30.210 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:30.277 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:30.343 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   

//Modify Clock
20:48:30.409 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 03FC 76   

20:48:30.475 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:30.541 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:30.607 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:30.673 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:30.705 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:30.770 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:30.836 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:30.903 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:30.969 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:31.033 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:31.066 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:31.131 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:31.197 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:31.261 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:31.325 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:31.390 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:31.455 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:31.521 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:31.587 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:31.653 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 00FF 40   
20:48:31.685 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   

20:48:31.749 -> FA14 32 30 34 39 0 0 0 0 1 4 00 00008002 1431 FF 0000000000 D0 FB06 64D40600 04FB 08  

20:48:31.814 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:31.878 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:31.945 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.010 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:32.077 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.143 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:32.208 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.241 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:32.306 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.372 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:32.437 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.503 -> FA14 20 20 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 D7 FB06 64D40600 00FF 40   
20:48:32.568 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.600 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:32.664 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.730 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:32.795 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.893 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:32.926 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:32.991 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:33.057 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:33.123 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:33.190 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:33.222 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:33.288 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:33.352 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:33.418 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:33.483 -> FA14 20 20 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 D7 FB06 64D40600 00FF 40   
20:48:33.549 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   

20:48:33.581 -> FA14 20 20 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 D7 FB06 64D40600 04FB 08   

20:48:33.680 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:33.745 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:33.810 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:33.843 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:33.909 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:33.975 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:34.040 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.106 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:34.139 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.203 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:34.269 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.334 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:34.400 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.464 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:34.528 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.593 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:34.659 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.725 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:34.757 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.823 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:34.888 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:34.955 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:35.020 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 01 FE52 00000000 0000 00   
20:48:35.086 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:35.119 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:35.183 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:35.282 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:35.348 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:35.380 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:35.445 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:35.510 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:35.575 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:35.642 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:35.709 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:35.742 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:35.808 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:35.873 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:35.939 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:36.004 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:36.070 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:36.137 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:36.203 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:36.268 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 01 FE52 00000000 0000 00   
20:48:36.301 -> FA14 32 30 35 31 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 78 FB06 64D40600 00FF 40   
20:48:36.367 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:36.433 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:36.499 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:36.565 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:36.596 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:36.662 -> FA14 32 30 35 31 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 78 FB06 64D40600 00FF 40   
20:48:36.726 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:36.792 -> FA14 32 30 35 31 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 78 FB06 64D40600 00FF 40   
20:48:36.857 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:36.922 -> FA14 32 30 35 31 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 78 FB06 64D40600 00FF 40   
20:48:36.986 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:37.053 -> FA14 32 30 35 31 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 78 FB06 64D40600 00FF 40   
20:48:37.118 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:37.185 -> FA14 32 30 35 31 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 78 FB06 64D40600 00FF 40   
20:48:37.217 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:37.282 -> FA14 32 30 35 31 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 78 FB06 64D40600 00FF 40   
20:48:37.348 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   

20:48:37.413 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 02FD 64   

20:48:37.479 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:37.545 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:37.577 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:37.676 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:37.741 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:37.808 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:37.841 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:37.906 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:37.970 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:38.035 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:38.100 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:38.165 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 00FF 40   
20:48:38.197 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   

20:48:38.262 -> FA14 32 30 35 30 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 7F FB06 64D40600 02FD 64   

20:48:38.327 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:38.393 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:38.457 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:38.521 -> FA14 32 30 20 20 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 1E FB06 64D40600 00FF 40   
20:48:38.586 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:38.652 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:38.719 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:38.785 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:38.816 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:38.882 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 00FF 40   
20:48:38.947 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   

20:48:39.014 -> FA14 32 30 34 39 0 0 0 0 1 4 47 00008002 1431 FF 0000000000 55 FB06 64D40600 04FB 08   

20:48:39.080 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.146 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:39.178 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.276 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:39.340 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.407 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:39.439 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.504 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:39.569 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.636 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:39.702 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.733 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:39.799 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.864 -> FA14 20 20 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 D7 FB06 64D40600 00FF 40   
20:48:39.930 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:39.997 -> FA14 20 20 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 D7 FB06 64D40600 00FF 40   
20:48:40.061 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:40.127 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:40.193 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:40.260 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:40.326 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   

20:48:40.357 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 04FB 08   
20:48:40.422 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:40.488 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:40.554 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:40.620 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:40.684 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:40.717 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:40.782 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:40.881 -> FA14 30 36 20 20 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 12 FB06 64D40600 00FF 40   
20:48:40.913 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:40.979 -> FA14 30 36 20 20 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 12 FB06 64D40600 00FF 40   
20:48:41.044 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:41.109 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:41.175 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:41.241 -> FA14 30 36 33 30 0 0 0 0 1 4 48 00008002 FFFF FF 0000000000 0D FB06 64D40600 00FF 40   
20:48:41.305 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 04 FB08 00000000 0000 00   
20:48:41.337 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:41.403 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:41.467 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:41.533 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:41.598 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:41.663 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:41.728 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:41.794 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:41.860 -> FA14 20 20 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 AE FB06 64D40600 00FF 40   
20:48:41.893 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:41.959 -> FA14 20 20 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 AE FB06 64D40600 00FF 40   
20:48:42.024 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:42.090 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:42.157 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:42.223 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:42.255 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:42.320 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:42.385 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   

20:48:42.484 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 04FB 08   
20:48:42.517 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:42.583 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:42.648 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:42.714 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:42.780 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:42.846 -> FA14 30 37 20 20 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 0E FB06 64D40600 00FF 40   
20:48:42.879 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:42.944 -> FA14 30 37 20 20 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 0E FB06 64D40600 00FF 40   
20:48:43.010 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:43.075 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   
20:48:43.142 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:43.175 -> FA14 30 37 32 35 0 0 0 0 1 4 49 00008002 FFFF FF 0000000000 1F FB06 64D40600 00FF 40   

20:48:43.273 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 04 FB08 00000000 0000 00   

20:48:43.340 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:43.371 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:43.436 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:43.501 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:43.566 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:43.633 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:43.699 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:43.763 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:43.796 -> FA14 20 20 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 37 FB06 64D40600 00FF 40   
20:48:43.859 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:43.923 -> FA14 20 20 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 37 FB06 64D40600 00FF 40   
20:48:43.989 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:44.087 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:44.119 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   

20:48:44.185 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 04FB 08   
20:48:44.251 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:44.317 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:44.382 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:44.414 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:44.480 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:44.545 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:44.610 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:44.677 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:44.742 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:44.775 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:44.874 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:44.940 -> FA14 31 32 20 20 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 41 FB06 64D40600 00FF 40   
20:48:44.972 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:45.037 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:45.102 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:45.169 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 00FF 40   
20:48:45.235 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   

20:48:45.300 -> FA14 31 32 32 35 0 0 0 0 1 4 4A 00008002 FFFF FF 0000000000 50 FB06 64D40600 04FB 08   
20:48:45.333 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:45.398 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:45.462 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:45.528 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:45.593 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:45.659 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:45.725 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:45.790 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:45.856 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:45.922 -> FA14 20 20 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 2B FB06 64D40600 00FF 40   
20:48:45.954 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:46.020 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:46.085 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:46.150 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:46.216 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 04 FB08 00000000 0000 00   
20:48:46.282 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:46.315 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:46.380 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:46.480 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:46.545 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:46.577 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:46.641 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:46.707 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:46.773 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:46.839 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:46.905 -> FA14 31 33 20 20 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 5D FB06 64D40600 00FF 40   
20:48:46.937 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.002 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:47.069 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.133 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 00FF 40   
20:48:47.198 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   

20:48:47.263 -> FA14 31 33 35 35 0 0 0 0 1 4 4B 00008002 FFFF FF 0000000000 27 FB06 64D40600 04FB 08   
20:48:47.329 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.396 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:47.462 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.494 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:47.560 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.625 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:47.692 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.758 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:47.822 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.855 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:47.920 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:47.985 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.051 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:48.116 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.180 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:48.246 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.312 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:48.377 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.409 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:48.475 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.540 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:48.606 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.672 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:48.738 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.770 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
20:48:48.869 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:48.935 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
20:48:49.002 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:49.033 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:49.099 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:49.163 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
20:48:49.229 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1431 FF 0000000000 C1 FB06 64D40600 00FF 40   
20:48:49.293 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00

TiSiAi Mar 16, 2023

@netmindz sorry, I create a bad file on GitHub .
Could you delete it ?

netmindz Mar 17, 2023
Maintainer Author

It's in your own fork, so would need to be you to delete if you don't want that branch

TiSiAi · 2023-03-16T20:17:18Z

TiSiAi
Mar 16, 2023

After lot of test, some command wasn't send after an FA14 Frame on second part
I test with the light pilot and I found that the command will sometime send after an AE0D Frame on second part

The command is the same : FB06 64D40600 09F6 C2
the 64D40600 is different on another GL or Keyboard
the CRC C2 will also different with your '64D40600' ID

//LIGHT
21:02:19.174 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:19.240 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:19.306 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:19.338 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
21:02:19.402 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:19.467 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
21:02:19.533 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:19.599 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:19.665 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:19.697 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:19.795 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:19.861 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
21:02:19.927 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:19.992 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
21:02:20.024 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40  

21:02:20.089 -> AE0D 02000000000000000000000000 C3 FB06 64D40600 09F6 C2        <<<< CMD ON Light with a FB06 after a AE0D frame !!!

21:02:20.155 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:20.221 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:20.287 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:20.352 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
21:02:20.385 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:20.451 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
21:02:20.516 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:20.581 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:20.647 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:20.711 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:20.777 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:20.843 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
21:02:20.909 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:20.942 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00   
21:02:21.008 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:21.073 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:21.138 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:21.203 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:21.270 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:21.335 -> AE0D 00 00 00 00 0 0 0 0 0 0 00 00000000 002D FB 0664D40600 00 FF40 00000000 0000 00   
21:02:21.402 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 00FF 40   
21:02:21.467 -> AE0D 01 00 00 00 0 0 0 0 0 0 00 00000000 005A FB 0664D40600 00 FF40 00000000 0000 00  

21:02:21.533 -> FA14 2D 2D 2D 2D 0 0 0 3 0 4 00 00088002 1502 FF 0000000000 48 FB06 64D40600 09F6 C2   <<<< CMD OFF Light 
21:02:21.565 -> AE0D 02 00 00 00 0 0 0 0 0 0 00 00000000 00C3 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:21.630 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40   
21:02:21.696 -> AE0D 03 00 00 00 0 0 0 0 0 0 00 00000000 00B4 FB 0664D40600 00 FF40 00000000 0000 00   
21:02:21.763 -> FA14 2D 2D 2D 2D 0 0 0 0 0 4 00 00008002 1502 FF 0000000000 7D FB06 64D40600 00FF 40

0 replies

tmjo · 2023-03-17T10:29:14Z

tmjo
Mar 17, 2023
Collaborator

Guys, this is super exciting news!

PS! Maybe we should refactor the library to use plain mqtt instead of the ha-mqtt integration? That would make it useful for everyone, not only us that use Home Assistant?

2 replies

TiSiAi Mar 17, 2023

When my test to control Tub finish, we analyse it ;)
@netmindz has do a big job today, we look with him
My work today is most the part of analysing control the Tub
I use your work to try help you :)

netmindz Mar 17, 2023
Maintainer Author

Not sure changing to vanilla MQTT, not sure the advantage of doing so. You can just ignore the extra messages if your MQTT setup isn't feeding into Home Assistant

TiSiAi · 2023-04-08T08:58:12Z

TiSiAi
Apr 8, 2023

@netmindz , @tmjo
It's ok for me and I can control the Tub
for debug I make a card with 2 signal input ( PIN5 from keyboard 2 and PIN5 from keyboard 3 )
i isolate the RS485 ground with TX/RX data converted with optocoupler ( very important if your wire are long )
when I use data from keyboard 2, it's for debug command send and keyboard 3 is use for my Controller
I make an application in BLE ( the response time is good for send the frame in less 2ms )
After receive a frame DATA FA14... I wait the end of the frame ( about 290us ) and after I send a command FB06
The end of the command must be send before the PIN5 return to 5V level
The timing is short and in this version, no wifi connexion
To Control the spa in this fist version, I have an iOS application

8 replies

TiSiAi Apr 10, 2023

your code in the main loop is for me with too process.
mqtt.loop();
ArduinoOTA.handle();
...
telnetLoop();
webserver.handleClient();
webSocket.loop();

String json = getStatusJSON();
if (json != lastJSON) {
webSocket.broadcastTXT(json);
lastJSON = json;
}

All this code if a client is connected is too long for processing Serial Data.

I think, you must Process Serial Data ( when pin5 is low, send a command if need ) and after send data on web connection ( no problem if you loose the next frame when PIN5 is low ).
Before a new Process, read empty serial data to clean and wait PIN5 go low

try your code without wifi for start.
use an button for example for up/temperature or you can use bluetooth ( BLE )

And after when its ok, add wifi

in my case, I m adding a wifi connexion and I will use MODBUS (via wifi ) for up speed. my first result are about 2/3 ms for send 4 uint16 value ( in this byte I encode the 8 bytes important for send the TUB information )

netmindz Apr 11, 2023
Maintainer Author

Hi @TiSiAi

I also have a minimal version https://github.com/netmindz/balboa_GL_ML_spa_control/blob/pin5/pin5test/pin5test.ino

This also didn't work, I'm not sure I can strip back any further.

Can you test my version with a scope to try and capture exactly how quickly I am responding in that most-minimal example?

netmindz Apr 12, 2023
Maintainer Author

I suspect the issue might relate to the fact my pin5test is not seeing the messages quite as i would expect, for example seeing FB messages. I should never see these if I'm only reading when pin5 for the main panel port I'm using. So something isn't quite right even for the most simple test of reading data at the right time to only see what i expect

netmindz Apr 12, 2023
Maintainer Author

e.g

EOM = ae0d02000000000000000000000000c3fb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6fb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6
EOM = fb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6fb0603450e0000ff74
EOM = ae0d03000000000000000000000000b4fb0603450e0000ff74
EOM = ae0d03000000000000000000000000b4
EOM = fb0603450e0000ff74
EOM = ae0d03000000000000000000000000b4fb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6fb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6
EOM = fb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6fb0603450e0000ff74
EOM = ae0d000000000000000000000000002dfb0603450e0000ff74
EOM = ae0d000000000000000000000000002d
EOM = fb0603450e0000ff74
EOM = ae0d000000000000000000000000002dfb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6fb0603450e0000ff74fa142d2d2d2d0000020000008002ffffff0000000000f6
EOM = fb0603450e0000ff74
EOM = fa142d2d2d2d0000020000008002ffffff0000000000f6fb0603450e0000ff74
EOM = ae0d010000000000000000000000005afb0603450e0000ff74
EOM = ae0d010000000000000000000000005a
EOM = fb0603450e0000ff74

TiSiAi Apr 12, 2023

Hello
I confirm you must no view FB command on your pin.

on pin from the original keyboard, FB response is present

TiSiAi · 2023-04-12T13:12:26Z

TiSiAi
Apr 12, 2023

I make a short of my code ( minimal to show you for analyse frame and when response with FB Command )

//Enable for analyse Original KeyBoard > no TX Data Enable
//#define DEBUG_ORIGINAL_KEYBOARD 1

int baudRate = SERIAL_8N1;
unsigned long baudTransmitExternalData=115200UL;
unsigned long lastExternalSerialDataValidTime = 2000UL;


//WARNING
//Replace with your PIN GPIO for RX/TX
#define rxPinExternalSerialData 14
#define txPinExternalSerialData 27
#define baudTransmitExternalData 115200


//WARNING
//Pin Keyboard
//>> modify with your PIN5 from your Keyboard
#define PIN_KEY_BOARD_1 16
#define PIN_KEY_BOARD_2 5  //my original Keyboard for debug FB Frame 

//Led state
#define ledGreen 26
#define ledRed 25


//Keyboard Command
//WARNING. replace 0x66,0x66,0x66,0x66  with your keyboard UID ( analyse your frame FB COMMAND to find it )
uint8_t keyboardCommand_UP[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x01,0xFE,0x52};
uint8_t keyboardCommand_DOWN[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x02,0xFD,0x64};
uint8_t keyboardCommand_TOGGLE[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x09,0xF6,0xC2};
uint8_t keyboardCommand_TIME[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x03,0xFC,0x76};
uint8_t keyboardCommand_CHANGE_MODE[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x04,0xFB,0x08};

uint8_t keyboardCommand_BLOWER[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x0A,0xF5,0xF4};

uint8_t keyboardCommand_JET1[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x06,0xF9,0x2C};
uint8_t keyboardCommand_JET2[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x07,0xF8,0x3E};

uint8_t keyboardCommand_EMPTY[] ={ 0xFB,0x06,0x66,0x66,0x66,0x66,0x00,0xFF,0x40};



int gpioKeyboardPin = PIN_KEY_BOARD_1; //Default ( my virtual new Keyboard with ESP32)

//Buffer pour la commande vers le SPA
#define maxSizeCommandBufferLength 16
int iCurrentCommandBufferLength=0;
uint8_t commandBuffer[maxSizeCommandBufferLength];

void clearCommandBuffer();


#define maxSizeDataBufferLength 200
int iLastPinState =0;

int iCurrentBufferLength=0;
int iPrecBufferLength=0;
uint8_t serialDataBuffer[maxSizeDataBufferLength];


unsigned long lastTimeLastData = 0;
unsigned long timeBeetweenFrame = 290UL;  //290us
unsigned long timeBeetweenFrame_original_keyboard = 1000UL;  //on laisse 1 ms au clavier d'origine

int nbFrameProcess = 0;
unsigned long lastTimeLastDataAnalysing = 0;
unsigned long timeBeetweenFrameAnalysing = 1*3000000UL;  //1ms

HardwareSerial SerialExternalDataTub(2); //27/17

int iPinState=-1;

//Function declaration
inline uint8_t crc8(uint8_t *data,uint8_t dataLength,uint8_t crcStart,uint8_t crcEnd);
void setCommand_SetTime();
void setCommand_SetProg();
void setCommand_SetUp();
void setCommand_SetDown();
void setCommand_SetJet1();
void setCommand_SetJet2();
void setCommand_SetLight();
void setCommand_SetBlower();



void setup() 
{
#ifdef DEBUG_ORIGINAL_KEYBOARD
    gpioKeyboardPin = PIN_KEY_BOARD_2;
#endif

  pinMode(PIN_KEY_BOARD_1, INPUT);
  pinMode(PIN_KEY_BOARD_2, INPUT);

  pinMode(ledGreen, OUTPUT);
  pinMode(ledRed, OUTPUT);

  digitalWrite(ledGreen,HIGH);
  digitalWrite(ledRed,HIGH);
  

  clearDataBuffer();
  clearCommandBuffer();
  
  Serial.begin(115200);

  delay(500);
  digitalWrite(ledGreen,LOW);
  delay(500);
  digitalWrite(ledRed,LOW);

  SerialExternalDataTub.setTimeout(2000);
  SerialExternalDataTub.begin(baudTransmitExternalData,baudRate,rxPinExternalSerialData,txPinExternalSerialData,false);
}


void clearDataBuffer()
{
  iCurrentBufferLength=0;
  memset(serialDataBuffer,0,maxSizeDataBufferLength);
}

//Buffer utilisé pour envoyé une commande au SPA
void clearCommandBuffer()
{
  iCurrentCommandBufferLength=0;
  memset(commandBuffer,0,maxSizeCommandBufferLength);
}


void loop() 
{

  ProcessSerialDataBuffer();

  //Temps de fin de Trame different si on analyse un clavier ou si c'est le notre
  //Quand on analyse un clavier, on doit attendre l envoi de la commande de retour ( > 1ms )
  //Sinon environ 300us
  unsigned long dynamicTimeBeetweenFrame = (gpioKeyboardPin==PIN_KEY_BOARD_1)?timeBeetweenFrame:timeBeetweenFrame_original_keyboard;
  
  if(((micros()-lastTimeLastData) > dynamicTimeBeetweenFrame) && (iCurrentBufferLength>1))
  {
    //if(iPinState>0) if use opto coupler ( the signal is reverse )
    if(iPinState<=0)
    {

      //Sample to prepare a command  ( add a command from a push button or wifi command, BLE )
      //setCommand_SetUp();

      //Envoyer tout de suite la commande au SPA sur une commande est préparée
      if(iCurrentCommandBufferLength>0)
      {
        sendCommandBuffer(commandBuffer,iCurrentCommandBufferLength);
        clearCommandBuffer();
      }

      //Print Data Frame
      PrintSerialBuffer(false);
    }
    
    clearDataBuffer();
  }
}


//Envoi de la commande sur la liaison série
void sendCommandBuffer(uint8_t* buffer,int bufferLength)
{
  //Sécurité, pas d'envoi de commande si on est en mode debug du clavier Physique
  if(gpioKeyboardPin!=PIN_KEY_BOARD_1)
  {
    Serial.println("Command not sended > Original KeyBoard");
    return;
  }

  if(bufferLength<=0)
  {
    Serial.println("Command not sended > No Data");
    return;
  }

  SerialExternalDataTub.write(buffer,bufferLength);
  
  Serial.print("SPA Cmd: ");
  for(int i=0;i<bufferLength;i++)
  {
    printHexa2Digit((byte)buffer[i],false);
  }
  Serial.println("");
} 



void PrintSerialBuffer(bool bActiveFilter)
{
  int iData=0;
  int iDataBuffer = 0;

  bool bFilter=false;

 
  if(iCurrentBufferLength>3)
  {
    //Enable if you want filter frame
    /*
    if((serialDataBuffer[0]==0xFA)&&(serialDataBuffer[1]==0x14))
    {
      bFilter=true;
    }
    */
    //Enable if you want filter frame
    /*
    if(serialDataBuffer[0]==0xAE)
    {
      bFilter=true;
    }
    */
  }

  if(bFilter && bActiveFilter)
  {
    return;
  }

  
  for(iDataBuffer=0;iDataBuffer<iCurrentBufferLength;iDataBuffer++)
  {
    iData=serialDataBuffer[iDataBuffer];
    printHexa2Digit((byte)iData,false);
  }
  if(iCurrentBufferLength>0)
  {
    Serial.print(" <");
    Serial.println(iCurrentBufferLength);
  }
}

//Empty all serial data
void EmptySerialDataBuffer()
{
  while(SerialExternalDataTub.available()) 
  { 
    SerialExternalDataTub.read();
  }
  clearDataBuffer();
}

bool ProcessSerialDataBuffer()
{
  int bPass=false;
  while(SerialExternalDataTub.available()) 
  { 
    if(!bPass)
    {
      bPass=true;
    }
    
    int iData = SerialExternalDataTub.read();
    if(iCurrentBufferLength<maxSizeDataBufferLength)
    {
      serialDataBuffer[iCurrentBufferLength]=(byte)iData;
      iCurrentBufferLength++;
    }
    else
    {
      EmptySerialDataBuffer();
      Serial.println("Overflow");
    }
  }

  //Si on a eu des données
  if(bPass)
  {
    lastTimeLastData = micros();
    iPinState = digitalRead(gpioKeyboardPin);
  }
}

void setCommand_SetTime()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_TIME);
  memcpy(commandBuffer,keyboardCommand_TIME,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_TIME");
}
void setCommand_SetProg()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_CHANGE_MODE);
  memcpy(commandBuffer,keyboardCommand_CHANGE_MODE,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_PROG");
}
void setCommand_SetUp()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_UP);
  memcpy(commandBuffer,keyboardCommand_UP,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_UP");
}
void setCommand_SetDown()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_DOWN);
  memcpy(commandBuffer,keyboardCommand_DOWN,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_DOWN");
}
void setCommand_SetJet1()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_JET1);
  memcpy(commandBuffer,keyboardCommand_JET1,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_JET1");
}
void setCommand_SetJet2()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_JET2);
  memcpy(commandBuffer,keyboardCommand_JET2,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_JET2");
}
void setCommand_SetLight()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_TOGGLE);
  memcpy(commandBuffer,keyboardCommand_TOGGLE,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_LIGHT");
}
void setCommand_SetBlower()
{
  clearCommandBuffer();
  int lengthCommand = sizeof(keyboardCommand_BLOWER);
  memcpy(commandBuffer,keyboardCommand_BLOWER,lengthCommand);
  iCurrentCommandBufferLength=lengthCommand;
  //Serial.println("CMD_SET_BLOWER");
}

void printHexa2Digit(byte iVal,bool bSplit)
{
  char buff[3];
  if(!bSplit)
  {
    sprintf(buff,"%02X",iVal);
    Serial.print(buff);
  }
  else
  {
    sprintf(buff,"%X",((iVal&0xF0)>>4));
    Serial.print(buff);
    Serial.print(" ");
    sprintf(buff,"%1X",iVal&0X0F);
    Serial.print(buff);
  }  

}


inline uint8_t crc8(uint8_t *data,uint8_t dataLength,uint8_t crcStart,uint8_t crcEnd)
{
  unsigned long crc;
  int i, bit;
  uint8_t length = dataLength;

  crc = crcStart;
  for ( i = 0 ; i < length ; i++ ) {
    crc ^= data[i];
    for ( bit = 0 ; bit < 8 ; bit++ ) {
      if ( (crc & 0x80) != 0 ) {
        crc <<= 1;
        crc ^= 0x7;
      }
      else {
        crc <<= 1;
      }
    }
  }
  return crc ^ crcEnd;
}

12 replies

netmindz Apr 13, 2023
Maintainer Author

I see you have a CRC method @TiSiAi but it appears unused. Can you provide an example where the command messages do not have the CRC at the end but are calculated by the code? Then we can more easily set our own UID in those commands

netmindz Apr 13, 2023
Maintainer Author

Ok, so I just tried a super simple test - https://github.com/netmindz/balboa_GL_ML_spa_control/blob/TiSiAi-example/just-send-test/just-send-test.ino

No effect, so changed to just keep writing non-stop, this should have "jammed" the rs485 bus, but that didn't block the other panel from working. So then realised that when I had once been able to send data before, I was using 5V for the RS485 adapter whereas I was using 3.3V now. Swapped to 5V and bingo, I get the light toggling. So then swapped back to trying to send based on delay after the pin goes low, but no luck.

It feels like there is some delay. Might the level shifter I'm using be introducing a delay?

TiSiAi Apr 13, 2023

I don't try to send a FB command with an other UID, I will try later
I don't use the CRC because I send directly the entire Frame I snif on my Keyboard .
Be Careful, on my code the last Byte of the command is the CRC, you will replace it because it is calculate with my UID

the last Byte 0x88 must be replace with the CRC result of the frame
uint8_t keyboardCommand_UP[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x01,0xFE,0x88};
 uint8_t keyboardCommand_DOWN[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x02,0xFD,0x88};
 uint8_t keyboardCommand_TOGGLE[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x09,0xF6,0x88};
 uint8_t keyboardCommand_TIME[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x03,0xFC,0x88};
 uint8_t keyboardCommand_CHANGE_MODE[] = { 0xFB,0x06,0x66,0x66,0x66,0x66,0x04,0xFB,0x88};

if possible, try my RS485 converter and analyse your signal with oscilloscope to verify the frame

TiSiAi Apr 13, 2023

Ok, so I just tried a super simple test - https://github.com/netmindz/balboa_GL_ML_spa_control/blob/TiSiAi-example/just-send-test/just-send-test.ino

I think it's a bad idea, the server wait a response just after the FA14 frame, you must send your command just after the end of the FA14 frame ( or other frame send when the pin5 is low ).

netmindz Apr 13, 2023
Maintainer Author

It's not meant to do anything other than just prove that I was actually writing to the the bus - it proved I wasn't due to hardware setup. Need that to be working before I try and do anything with software

netmindz · 2023-04-13T15:25:03Z

netmindz
Apr 13, 2023
Maintainer Author

@tmjo If you wish to try the code from @TiSiAi it's under https://github.com/netmindz/balboa_GL_ML_spa_control/blob/TiSiAi-example/TiSiAi-example/TiSiAi-example.ino

1 reply

tmjo Apr 14, 2023
Collaborator

Hi! I'm following your interesting discussions closely and with great hope :) I still didn't get around to fill my tub yet, so I haven't been able to test anything yet. Getting a bit warmer in the air, so I'll probably risk myself going outdoors and give the good ol' lady a spring treat.

netmindz · 2023-05-03T20:57:57Z

netmindz
May 3, 2023
Maintainer Author

I have control of my light 🥳🎉

4 replies

TiSiAi May 3, 2023

cool
Easy now for other command ;)

netmindz May 5, 2023
Maintainer Author

Are you able to share the full source @TiSiAi of your app so I can see how you handle things like setting a specific temp or changing mode, where you need to press mode then up and down to get to where you want. I see you have the empty command, so do you need to send mode, then delay before you send the up or down presses

netmindz May 13, 2023
Maintainer Author

For the example you shared, is 6666 really your FB command or had you replaced it with an example value and not updated the CRC value? Certainly your examples give me no response, but it would make the project much easier to use if people don't need to "sniff" an existing control panels command.

TiSiAi Jun 14, 2023

Hello
Sorry, I don't see the notification.
//WARNING. replace 0x66,0x66,0x66,0x66 with your keyboard UID ( analyse your frame FB COMMAND to find it )
My full is only with a BT communication and adapted with ma iOS application, I have post all command
I use it since 15 May every day and it's OK for me

netmindz · 2023-05-13T17:31:13Z

netmindz
May 13, 2023
Maintainer Author

Ok, so I have a branch (send-command-queue) up and running that reliably lets me swap the tub into and out of Eco as well as toggle the lights from Home Assistant @tmjo

As my electricity price changes depending on the time of day, Home Assistant can control the heating to only be when the price is cheap and I can also take the tub out of Sleep when I'm on my way back home so it's nice and warm for my return if I go away for a few days and don't want to leave the tub on full

0 replies

tmjo · 2023-05-13T21:07:41Z

tmjo
May 13, 2023
Collaborator

@netmindz: That sounds amazing!! Congratulations on the good job, I can't wait to test it out! Your price dependent control is exactly one of the reasons why I'm so keen on controlling the spa too! Also because I have an electric car charging during night, so I need to reduce the total power to save some money (my bill also depends on the top three hourly average power consumptions, so good to stay below a threshold).

In fact, I was out today to clean the spa, fill it up and start it up after some time de-commissioned since we were away for several months. I had even prepared my interface with the pin5 to take part of the new discoveries you've done over the past months. Needless to say, there were not just pretty words coming out of my mouth when the RCD tripped on ground fault immediately as I powered up the old lady. After some troubleshooting, I've found out my heater element has ground fault, so I have taken it out to see if there is anything to do with it or if I should just buy a new one. The spa was powered successfully without the heater, so pretty sure that is the cause of my troubles, but then again, what is a spa without a heater :)

Anyways, will take another couple of weeks before I'm back online with the spa, but I'll keep updated here and let you know when I'm ready. Really looking forward to it. I'll see if I can upgrade to ESP32 and the newer RS485-board as well instead of my 8266+MAX485 setup.

Cheers and thanks for all your efforts!

6 replies

netmindz May 15, 2023
Maintainer Author

Given how cheap the esp32 are now, probably makes sense for us both to be on the same platform. I got swap back to MAX485 for a bit after hardware fault, but I'm back to the new style since working on the send code as has status LEDs

nzlamb May 18, 2023

Jumping in - been following this thread for a month or so as I've just started out with Home Assistant and can't believe the timing of this work!

FWIW I had the same problem and recently replaced the heater in my GL2000 with a genuine Balboa replacement and it's been good ever since. The new ones come with flexible cables instead of the copper straps which reduces stress on the terminals and makes replacement much easier.

I've since found aftermarket bare replacement elements much cheaper on Amazon that I might try next time, but the unions and gaskets on mine were shot as well it was good having the complete Balboa kit that included new plumbing hardware and temperature sensors.

nzlamb May 18, 2023

Also, just wanted to thank you all for the effort you've put into this!

I've got a ML700 control panel on mine in case there's any useful data I can log off it once I get my ESP all connected up.

netmindz May 18, 2023
Maintainer Author

Nice to hear from you @nzlamb let me know how you get on getting set-up

netmindz Jun 20, 2023
Maintainer Author

How are you getting along @nzlamb ?

tmjo · 2023-06-11T18:29:11Z

tmjo
Jun 11, 2023
Collaborator

@netmindz; I'm slowly getting there. Received a new heater this week and have my brand new ESP32 including PSU and modern RS485 board wired up with software running. Thought I was ready to power up this weekend, but realized I just received a single gasket when I thought it was a package with two. Hope to get the second one this week and I'm really looking forward to check out the new stuff!!

Just to be sure I'm up to date on latest achievements: The send-command-queue branch is the latest and greatest you're working on when it comes to sending right? And by end of the day you connected the pin5 directly to ESP32 (with disclaimers for sure), correct?

Btw; did you ever consider esphome as a "platform"? I though it would be kindof limiting, but then I found a Mitsubishi heatpump sourcecode that I've been using on an ESP for years elegantly integrated with esphome. Seems like it takes an external repo and just adds a 'shell' around to integrate it into HA/Esphome. Could be an interesting approach. Anyway, this is not important right now, let's get all the stuff working and then we can look for such improvements. Just thought I'd let you know, it looks interesting in my opinion, especially since it makes staying up-to-date really easy for all users (and everything handled within HA).

2 replies

tmjo Jun 14, 2023
Collaborator

Alright, the grand old lady is sailing again. Got my last gasket today, mounted the "new" heater and I've got everything up and running again with the new ESP32. Letting the tub heat up over night, and hope to do some hacking next week. Looking forward to test the commands.

netmindz Jun 16, 2023
Maintainer Author

yeah, send-command-queue is the latest and greatest and yes you will need pin5 connected, I found the level shifter I tried to use too slow to respond. A voltage divider with resistors is probably a cheap, simple option, and probably fast too, but not tried that myself.

caldog20 · 2023-06-12T01:04:59Z

caldog20
Jun 12, 2023

I just recently got a tub from a family member that was non-working. Turns out the board had 2 bad diodes in the sensor comparitor circuit due to a stuck heater relay and water being too hot for too long. I repaired the board, and it functions normally but topside ml700 is half working. I ordered an RS485 TTL converter and a few other supplies to start working with this project. I'd be happy to help contribute as much as possible. The only downside is that I don't yet have an oscilloscope, but will soon. Let me know if there is anything I can do to help. My plan is to try to help contribute to sending commands for controlling the unit remotely.

Excited to get started with this.

3 replies

netmindz Jun 16, 2023
Maintainer Author

Hi @caldog20 , should be no need for an oscilloscope, I think we are past that point now

Start by following the install guide to get the basic read-only version of this project working for you. Once you have that running, I can send you some notes on the newer version that handled controlling some of the tub functions as well

netmindz Jun 16, 2023
Maintainer Author

p.s how did you find this project?

caldog20 Jun 16, 2023

I was doing research on this board/topside and when the topside stopped working properly I started looking into the communication method/protocol between board and topside. I finally found this which was great because I have this board and also enjoy doing embedded programming and reverse engineering. I contribute to open source projects in my spare time so I am always on github.

StumpyRob · 2023-06-14T18:58:36Z

StumpyRob
Jun 14, 2023

This is really interesting. I have ordered my parts. I'm going to give it a go! Thank you for your work on this! :)

3 replies

netmindz Jun 16, 2023
Maintainer Author

Hi @StumpyRob - where did you find out about this project?

StumpyRob Jun 16, 2023

I stumbled across it on the Home assistant forum, I was looking at trying to get my GL2000 series integrated with HS thought it couldn't be done with the older GL units then came across your post mentioning this project. 🥇

Still waiting on bits to arrive - I don't think I will have time this weekend but I am planning on having a play next weekend with it. I expect I will be back with some queries next week!

netmindz Jun 16, 2023
Maintainer Author

Great - I tried to spam a few of the different threads about Balboa stuff when I first started this in the hope of finding others to help me work on this project. Didn't get much/any of a response, but good to hear you were able to find one. If you could post a comment to the thread you found to help bump it's visibility that would be appreciated

netmindz · 2023-06-16T11:55:11Z

netmindz
Jun 16, 2023
Maintainer Author

As between us all, we have more or less cracked the usage of the key pins, and the format of the protocol, I'm going to close this thread and open up two new discussions for initial setup feedback and another for the work on sending specific commands to the tub

0 replies

Ideas on protocol format #3

netmindz Mar 15, 2022 Maintainer

Replies: 24 comments · 67 replies

netmindz Mar 15, 2022 Maintainer Author

netmindz Mar 16, 2022 Maintainer Author

netmindz Jun 15, 2022 Maintainer Author

netmindz Mar 20, 2022 Maintainer Author

netmindz Mar 26, 2022 Maintainer Author

netmindz Apr 17, 2022 Maintainer Author

netmindz Jun 14, 2022 Maintainer Author

netmindz Apr 17, 2022 Maintainer Author

tmjo Apr 18, 2022 Collaborator

netmindz Jun 15, 2022 Maintainer Author

netmindz May 24, 2022 Maintainer Author

netmindz Sep 24, 2022 Maintainer Author

tmjo Sep 29, 2022 Collaborator

netmindz Oct 5, 2022 Maintainer Author

netmindz Oct 5, 2022 Maintainer Author

netmindz Oct 9, 2022 Maintainer Author

tmjo Oct 11, 2022 Collaborator

netmindz Oct 13, 2022 Maintainer Author

netmindz Mar 16, 2023 Maintainer Author

netmindz Mar 16, 2023 Maintainer Author

netmindz Mar 16, 2023 Maintainer Author

tmjo Mar 16, 2023 Collaborator

netmindz Mar 16, 2023 Maintainer Author

netmindz Mar 16, 2023 Maintainer Author

netmindz Mar 17, 2023 Maintainer Author

tmjo Mar 17, 2023 Collaborator

netmindz Mar 17, 2023 Maintainer Author

netmindz Apr 11, 2023 Maintainer Author

netmindz Apr 12, 2023 Maintainer Author

netmindz Apr 12, 2023 Maintainer Author

netmindz Apr 13, 2023 Maintainer Author

netmindz Apr 13, 2023 Maintainer Author

netmindz Apr 13, 2023 Maintainer Author

netmindz Apr 13, 2023 Maintainer Author

tmjo Apr 14, 2023 Collaborator

netmindz May 3, 2023 Maintainer Author

netmindz May 5, 2023 Maintainer Author

netmindz May 13, 2023 Maintainer Author

netmindz May 13, 2023 Maintainer Author

tmjo May 13, 2023 Collaborator

netmindz May 15, 2023 Maintainer Author

netmindz May 18, 2023 Maintainer Author

netmindz Jun 20, 2023 Maintainer Author

netmindz
Mar 15, 2022
Maintainer

Replies: 24 comments 67 replies

netmindz
Mar 15, 2022
Maintainer Author

netmindz
Mar 16, 2022
Maintainer Author

netmindz Jun 15, 2022
Maintainer Author

netmindz
Mar 20, 2022
Maintainer Author

netmindz
Mar 26, 2022
Maintainer Author

netmindz
Apr 17, 2022
Maintainer Author

netmindz Jun 14, 2022
Maintainer Author

netmindz
Apr 17, 2022
Maintainer Author

tmjo Apr 18, 2022
Collaborator

netmindz Jun 15, 2022
Maintainer Author

netmindz
May 24, 2022
Maintainer Author

netmindz
Sep 24, 2022
Maintainer Author

tmjo Sep 29, 2022
Collaborator

netmindz Oct 5, 2022
Maintainer Author

netmindz Oct 5, 2022
Maintainer Author

netmindz
Oct 9, 2022
Maintainer Author

tmjo Oct 11, 2022
Collaborator

netmindz
Oct 13, 2022
Maintainer Author

netmindz Mar 16, 2023
Maintainer Author

netmindz Mar 16, 2023
Maintainer Author

netmindz Mar 16, 2023
Maintainer Author

tmjo
Mar 16, 2023
Collaborator

netmindz Mar 16, 2023
Maintainer Author

netmindz Mar 16, 2023
Maintainer Author

netmindz Mar 17, 2023
Maintainer Author

tmjo
Mar 17, 2023
Collaborator

netmindz Mar 17, 2023
Maintainer Author

netmindz Apr 11, 2023
Maintainer Author

netmindz Apr 12, 2023
Maintainer Author

netmindz Apr 12, 2023
Maintainer Author

netmindz Apr 13, 2023
Maintainer Author

netmindz Apr 13, 2023
Maintainer Author

netmindz Apr 13, 2023
Maintainer Author

netmindz
Apr 13, 2023
Maintainer Author

tmjo Apr 14, 2023
Collaborator

netmindz
May 3, 2023
Maintainer Author

netmindz May 5, 2023
Maintainer Author

netmindz May 13, 2023
Maintainer Author

netmindz
May 13, 2023
Maintainer Author

tmjo
May 13, 2023
Collaborator

netmindz May 15, 2023
Maintainer Author

netmindz May 18, 2023
Maintainer Author

netmindz Jun 20, 2023
Maintainer Author