Insert the power modules and stack modules on the switches :
Pwer on the switches and connect the
Connect the console cable on switch 1 and type sh run
stacking
member 1 type “JL075A” mac-address 70106f-8a3b00
exit
Insert the stack cable in port 1 switch 1
on the log appear :
I 10/20/16 03:55:37 02556 chassis: ST1-CMDR: Stack port 1 cable inserted
Insert the stack cable in port 1 switch 2
on the log appear :
I 10/20/16 04:02:58 02558 chassis: ST1-CMDR: Stack port 1 is now on-line.
W 10/20/16 04:02:59 03270 stacking: ST1-CMDR: Topology is a Chain
I 10/20/16 04:02:59 03279 stacking: ST1-CMDR: Member 2 (70106f-8df200) chosen as
standby. Reason: Only available standby
the switch 2 is start to reload :
I 10/20/16 04:02:59 03125 mgr: ST1-CMDR: Startup configuration changed by SNMP.
New seq. number 1
I 10/20/16 04:03:14 03272 stacking: ST1-CMDR: Stack fragment active
I 10/20/16 04:03:19 02559 chassis: ST1-CMDR: Stack port 1 is now off-line.
I 10/20/16 04:04:10 02558 chassis: ST1-CMDR: Stack port 1 is now on-line.
I 10/20/16 04:04:10 03279 stacking: ST1-CMDR: Member 2 (70106f-8df200) chosen as
standby. Reason: Only available standby
I 10/20/16 04:04:22 03846 InSysProg: ST1-CMDR: Slot 2/17-21: Checking for
firmware updates.
I 10/20/16 04:04:22 00375 chassis: ST1-CMDR: Slot 2/17-21 Downloading
I 10/20/16 04:04:23 00376 chassis: ST1-CMDR: Slot 2/17-21 Download Complete
I 10/20/16 04:04:23 03846 InSysProg: ST1-CMDR: Slot 2/1-8: Checking for firmware
updates.
I 10/20/16 04:04:23 00375 chassis: ST1-CMDR: Slot 2/1-8 Downloading
I 10/20/16 04:04:23 00376 chassis: ST1-CMDR: Slot 2/1-8 Download Complete
I 10/20/16 04:04:24 03846 InSysProg: ST1-CMDR: Slot 2/9-16: Checking for
firmware updates.
I 10/20/16 04:04:24 00375 chassis: ST1-CMDR: Slot 2/9-16 Downloading
I 10/20/16 04:04:25 00376 chassis: ST1-CMDR: Slot 2/9-16 Download Complete
I 10/20/16 04:04:28 00422 chassis: ST1-CMDR: Slot 2/17-21 Ready
W 10/20/16 04:04:28 03270 stacking: ST1-CMDR: Topology is a Chain
I 10/20/16 04:04:28 00539 stacking: ST1-CMDR: Initial sync to standby starting
I 10/20/16 04:04:32 00422 chassis: ST1-CMDR: Slot 2/1-8 Ready
I 10/20/16 04:04:33 00422 chassis: ST1-CMDR: Slot 2/9-16 Ready
I 10/20/16 04:04:39 00540 stacking: ST1-CMDR: Redundant Standby Management
Module syncing is in progress. Configuration changes are temporarily
blocked
M 10/20/16 04:04:39 02796 chassis: ST2-STBY: Internal power supply 1 inserted.
Total fault count: 0.
M 10/20/16 04:04:39 02796 chassis: ST2-STBY: Internal power supply 2 inserted.
Total fault count: 0.
M 10/20/16 04:04:39 02797 chassis: ST2-STBY: Internal power supply 2 is OK.
Total fault count: 0.
I 10/20/16 04:05:28 03260 stacking: ST2-STBY: Member booted
I 10/20/16 04:05:28 03272 stacking: ST1-CMDR: Stack active
I 10/20/16 04:05:28 00540 stacking: ST1-CMDR: Redundant Standby Management
Module syncing is complete. Configuration changes are allowed
at the end, the switch 2 is on standby mode
Aruba-Stack-3810M# sh stacking
Stack ID : 00027010-6f8a3b00
MAC Address : 70106f-8a3b64
Stack Topology : Chain
Stack Status : Active
Split Policy : One-Fragment-Up
Uptime : 0d 0h 27m
Software Version : KB.16.01.0004
Mbr
ID Mac Address Model Pri Status
— ————- ————————————– — —————
1 70106f-8a3b00 Aruba JL075A 3810M-16SFP+-2-slot Sw… 128 Commander
2 70106f-8df200 Aruba JL075A 3810M-16SFP+-2-slot Sw… 128 Standby
sh run
stacking
member 1 type “JL075A” mac-address 70106f-8a3b00
member 2 type “JL075A” mac-address 70106f-8df200
type write to save the configuration and show stack to verify the stack status