HP 2530 8-Port Switches Quick Setup Guide

HP 2530 8-Port Switches Quick Setup Guide
The switch drawings in this document are for illustration only and may not match your particular switch model.
For more detailed instructions and information to set up your switch, view or download the Installation and Getting Started
Guide for your switch at www.hp.com/networking/support.
1. Unpack and check included parts.
■
■
■
■
■
Switch
Console port serial cable (DB-9 to RJ-45)
Accessory kit (installation hardware)
AC/DC power adapter module and power cord
Documentation kit
2. Prepare for installation. To avoid personal injury or product damage, review the “Installation Precautions” on page 3.
3. Power on and verify Self-Test completes normally. The switch does not contain a power switch. It is turned on by
connecting the AC/DC power adapter.
After Self-Test:
Power LED = On
Fault LED = Off
Test LED = Off
4. Install the Switch Hardware. Power off the switch before installing the switch hardware.
(Optional) Attach accessories: The following accessories can be installed on your HP 2530 8-port switch:
■
A cable guard (HP P/N J9700A) to provide security for the attached network cables.
■
A power shelf (HP P/N J9820A) to hold the AC/DC power adapter.
For instructions to install these accessories, see the documentation that is included with them.
Table or Desktop: Attach the four self-adhesive pads
(included in the accessory kit) to the bottom corners of the
switch and place the switch on a secure horizontal surface.
Wall or Under-Table: For wall or under-table mounting, use
a #1 Phillips (cross-head) screwdriver and the 20-mm M4 tap
screws (included). The screws should be positioned 90 mm
apart, with the screw heads approximately 2 mm away from
the mounting surface to allow the switch to slide onto the
screws. (Under-Table: After installation, a third screw may be
installed to prevent switch movement.)
M-4 tap
screws
Caution: For wall-mounting, the network ports must face up.
Do not mount the switch with ventilation ducts facing up or
down. (See “Installation Precautions” on page 3.)
Ventilation
1
4. Install the Switch Hardware (Continued)
Rack Mounting: A rack-mounting kit is included with your switch. Use a #1 Phillips (cross-head) screwdriver to attach the
rack brackets to the switch using the eight 8-mm M4 screws. Then use the four number 12-24 screws to secure the brackets
to the rack.
5. (Optional) Lock the Switch. Use a Kensington lock or similar
device (not included) to physically secure the switch.
6. Power On the Switch and Secure the Power Connector.
Use the cable tie in the accessory kit, and the retention tab on the
switch, to secure the power connector.
Cable tie
Retention
tab
7. Connect Network Cables.
Note: For transceiver connections, use only HP-supported SFP
transceivers. See “SFP Installation Notes” on page 3.
8. (Optional) Configure the Switch for Management.
By factory default, the switch will automatically obtain its IP
network configuration from a DHCP or BootP server. Subsequently,
you can determine the IP address assigned to the switch by
inspecting your DHCP/BootP server, or by using LLDP from a
connected device.
You can also manage and configure the switch through a console
port connection. Connect a VT-100 terminal or PC (with suitable
terminal emulation software) to the switch using the serial cable
(DB-9 and RJ-45 connectors) supplied with the switch.
* Note: You can also connect a console to the switch via the USB
console port (cable not provided). Use a USB 2.0 high-speed cable
with a male type A (4-pin) to male micro-B (5-pin) connector.
Maximum allowable length is 5m. For more information on using
the USB console port, see the Installation and Getting Started
Guide for your switch.
For information on configuration and remote management, see the
Management and Configuration Guide for your switch at
www.hp.com/networking/support.
2
Console port
RJ-45 to DB9
Console cable
supplied with
the switch
Optional USB
Console cable
(not supplied) *
To PC running a
terminal emulator
program, or a
VT-100 terminal
SFP Installation Notes
■
Use only genuine HP SFPs. Non-HP SFP transceivers are not supported. Use of genuine HP products ensures that
your network maintains optimal performance and reliability. Should you require additional transceivers, please contact
an HP sales representative or an authorized reseller.
■
Hot Swapping SFP transceivers. Supported SFP transceivers that you can install in your HP switch can be “hot
swapped” – removed and installed while the switch is receiving power. You should disconnect the network cables from
the SFP transceivers before hot-swapping them, though.
When you replace a SFP transceiver with another of a different type, the switch may retain selected port-specific
configuration settings that were configured for the replaced unit. Be sure to validate or reconfigure port settings as required.
■
SFP Connections to Devices with Fixed Speed/Duplex Configurations. When connecting a device to your switch
port that contains an SFP transceiver, the speed and duplex settings of the switch port and the connected device must
match; otherwise, the device may not link properly — you may not get a link. For some older network devices, including
some older HP devices, the default speed/duplex settings may be predefined (for example, to 1000 Mbps/Full Duplex),
or otherwise set differently from the default configuration of your switch port. Because of these default speed/duplex
considerations, you should make sure that devices connected to your SFP ports are properly configured. At a
minimum, make sure the configurations match.
■
Environmental limitations. If using SFPs with the switch, make sure that the operating temperature range at the
switch installation site does not exceed the range allowed for the SFP.
Safety and Regulatory Information for HP 2530 8-Port Switches
To avoid personal injury or product damage when installing your switch, read the installation precautions and guidelines below.
Installation Precautions
Warnings
■
The rack or cabinet should be adequately secured to prevent it from becoming unstable, tilting or falling.
Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices at the
bottom and progressively lighter devices above.
■
Wall-mount the switch with network ports facing up (away from the floor).
Do not wall-mount the switch with the network ports facing down (toward the floor) or ventilation ducts
facing up or down.
Cautions
■
■
■
■
■
■
■
Use only the AC/DC power adapter supplied with the switch for connection to an AC power source.
Ensure the power source circuits are properly grounded, then use the power cord supplied with the switch to connect
the AC/DC power adapter to the AC power source.
If your installation requires a different power cord than the one supplied with the switch and/or power supply, be
sure the cord is adequately sized for the switch’s current requirements. In addition, be sure to use a power cord
displaying the mark of the safety agency that defines the regulations for power cords in your country/region. The
mark is your assurance that the power cord can be used safely with the switch and power supply.
When installing the switch, the AC outlet should be near the switch and should be easily accessible in case the switch
must be powered off.
Ensure the switch does not overload the power circuits, wiring, and over-current protection. To determine the
possibility of overloading the supply circuits, add together the ampere ratings of all devices installed on the same
circuit as the switch and compare the total with the rating limit for the circuit. The maximum ampere ratings are
usually printed on the devices near the AC power connectors.
Do not install the switch in an environment where the operating ambient temperature exceeds its specification.
Ensure the air flow around the switch is not restricted. Leave at least 7.6 cm (3 inches) for cooling. For other available
air flow information, see the Installation and Getting Started Guide for your product, located on the HP Web site
at www.hp.com/networking/support.
3
For additional safety and regulatory information, and switch recycling information, refer to the safety and regulatory
documentation on the HP web site at www.hp.com/support/Safety-Compliance-EnterpriseProducts, and to the HP 2530
Switch Installation and Getting Started Guide that can be found on the HP Networking web site: www.hp.com/networking/
support.
Product Specifications
Electrical:
HP 2530-8G-PoE+ Switch (J9774A)
HP 2530-8-PoE+ Switch (J9780A)
HP 2530-8G Switch (J9777A)
HP 2530-8 Switch (J9783A)
Requires a connection to external power
adapter module 5066-2164 (supplied with
these switches). Use only this adapter:
Requires a connection to external power
adapter module 5066-2695 (supplied with
this switch). Use only this adapter:
Requires a connection to external power
adapter module 5066-1122 (supplied with
this switch). Use only this adapter:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
AC Input Voltage: 100-240 V
Maximum AC Input Current: 1.40 A
AC Input Frequency Range: 50/60 Hz
Maximum DC Output Power: 90 W
DC Output Voltage: 54 V
Maximum DC Output Current: 1.67 A
Environmental:
Operating Temperature:
Operating Relative humidity:
Non-Operating Temperature:
Non-Operating Relative
humidity:
AC Input Voltage: 100-240 V
Maximum AC Input Current: 0.50 A
AC Input Frequency Range: 50/60 Hz
Maximum DC Output Power: 15 W
DC Output Voltage: 12 V
Maximum DC Output Current: 1.25 A
0°C to 45°C (32°F to 104°F)
15% to 95% at 40°C (104°F), non-condensing
-40°C to 70°C (-40°F to 158°F)
15% to 95% at 65°C (149°F), non-condensing
Maximum Operating Altitude:
Up to 3.05 km (10,000 feet)
Non-Operating Altitude:
Up to 4.57 km (15,000 feet)
Acoustic:
AC Input Voltage: 100-240 V
Maximum AC Input Current: 0.50 A
AC Input Frequency Range: 50/60 Hz
Maximum DC Output Power: 18 W
DC Output Voltage: 12 V
Maximum DC Output Current: 1.50 A
Power: 0 dB (no fan)
Safety:
Standards:
Lasers:
EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011; IEC 60950-1:2005 (2nd Edition); Am 1:2009
EN 60825-1:2007 / IEC 60825-1:2007 Class 1
Class 1 Laser Products / Laser Klasse 1
HP 2530-8G-PoE+ (J9774A), 2530-8G (J9777A), 2530-8-PoE+ (J9780A), 2530-8 (J9783A) Switches:
WARNING
FOR INDOOR USE ONLY. The switch, AC power cord and adapter, and all connected cables are not designed for outdoor use.
HP 2530-8-PoE and 2530-8G-PoE External Power Adapter and Power Cords:
External AC/DC Power Adapter
All countries/regions
Power Cords
5066-2164 Argentina
Australia/New Zealand
Brazil
Chile
China
Continental Europe
Denmark
India
Israel
8120-6869
8121-0834
8121-1069
8120-6980
8120-8377
8120-6802
8120-6806
8121-0780
8121-1035
(continued on the next page)
4
Japan
Malaysia
Switzerland
South Africa
South Korea
Taiwan
Thailand
United Kingdom/Hong Kong/Singapore
United States/Canada/Mexico
8120-6804
8120-6809
8120-6807
8121-0919
8120-6811
8121-0964
8121-0673
8120-6809
8120-6805
HP 2530-8 and 2530-8G External Power Adapters and Power Cords:
External AC/DC Power Adapters
All countries/regions
Power Cords
5066-1122 Argentina
5066-2695 Australia/New Zealand
Brazil
Chile
China
Continental Europe
Denmark
India
Israel
8120-8367
8121-0870
8121-1081
8121-0514
8120-8373
8120-6314
8120-6314
8121-0702
8120-6314
Japan
Malaysia
Switzerland
South Africa
South Korea
Taiwan
Thailand
United Kingdom/Hong Kong/Singapore
United States/Canada/Mexico
8120-6316
8120-8699
8120-6314
8120-6317
8120-8441
8121-0963
8121-0664
8120-8699
8120-6313
Japan Power Cord Warning
Important Note for the 2530-PoE+ Switches
For PoE/PoE+ information see the HP Power over Ethernet (PoE/PoE+) Planning and Implementation Guide on the HP
web site at: www.hp.com/networking/support.
5
© Copyright 2013 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
Printed in China
February 2013
5998-3635
*5998-3635*